Malangizo Ogwiritsira Ntchito
R37 - 3 Zone Programmer
Zofunika: Sungani chikalata ichi Wopanga pulogalamu ya zone 3 adapangidwa kuti aziwongolera ON/OFF m'magawo atatu, ndikugwiritsanso ntchito muchitetezo cha chisanu ndi loko yamakiyi.
CHENJEZO! Musanayambe, chotsani chipangizocho ku mains mains. Pali magawo omwe amanyamula mains voltage kuseri kwa chivundikirocho. Osasiya osayang'anira ikatsegulidwa. (Letsani anthu omwe si akatswiri komanso makamaka ana kuti azitha kuzipeza.) Osachotsa mankhwalawa pamagetsi amagetsi. Lumikizani ku mains mains pakawonongeka kulikonse pamabatani aliwonse. Osagwiritsa ntchito zida zakuthwa kukankha batani lililonse.
Zokonda zokhazikika pafakitale
| Pulogalamu: | 5/2D |
| Kumbuyo: | On |
| Kiyibodi: | Zotsegulidwa |
| Chitetezo cha Frost | Osati |
Zokonda pulogalamu ya fakitale
|
5/2D | |||||
| P1 PA | P1 KUZIMA | P2 PA | P2 KUZIMA | P3 PA | P3 KUZIMA | |
| Lolemba-Lachisanu | 6:30 | 8:30 | 12:00 | 12:00 | 16:30 | 22:30 |
| Sat-Sun | 7:30 | 10:00 | 12:00 | 12:00 | 17:00 | 23:00 |
| Masiku onse 7 | 7D | |||||
| P1 PA | P1 KUZIMA | P2 PA | P2 KUZIMA | P3 PA | P3 KUZIMA | |
| 6:30 | 8:30 | 12:00 | 12:00 | 16:30 | 22:30 | |
| Tsiku lililonse | 24H | |||||
| P1 PA | P1 KUZIMA | P2 PA | P2 KUZIMA | P3 PA | P3 KUZIMA | |
| 6:30 | 8:30 | 12:00 | 12:00 | 16:30 | 22:30 | |
Kukhazikitsanso pulogalamu
Ndikofunikira kukanikiza batani la RESET musanayambe kukonza mapulogalamu.
batani ili lili kuseri kwa chivundikiro kutsogolo kwa unit.
Kukhazikitsa tsiku ndi nthawi
Tsitsani chophimba kutsogolo kwa unit.
Sunthani chosinthira chosankha kupita pamalo a CLOCK SET.
Dinani pa 
or 
mabatani kusankha tsiku. Press 
Dinani pa or mabatani kusankha mwezi. Press
Dinani pa or mabatani kusankha chaka. Press
Dinani pa or mabatani kusankha ola. Press
Dinani pa or mabatani kusankha miniti. Press
Dinani pa or mabatani kuti musankhe 5/2D, 7D kapena 24H Press
Tsiku, nthawi ndi ntchito tsopano zakhazikitsidwa. Sunthani chosinthira chosankha kupita pa RUN udindo kuti muyendetse pulogalamuyi, kapena pa PROG SET pomwe musinthe makonzedwe a pulogalamuyo.
ON/OFF kusankha nthawi
Pali mitundu inayi yomwe ilipo pa pulogalamu iyi kuti ogwiritsa ntchito asankhe payekhapayekha.
AUTO Wopanga mapulogalamu amagwira ntchito 3 'ON/OFF' patsiku.
TSIKU LONSE Wopanga mapulogalamu amagwira ntchito 1'ON/OFF' patsiku.
Izi zimagwira ntchito kuyambira nthawi yoyamba ON mpaka nthawi yachitatu OFF.
ON Wopanga mapulogalamu amayatsidwa mpaka kalekale. **PA**
ZIZIMA Wopanga mapulogalamuwa wazimitsidwa. **KUDZIWA**
Tsitsani chophimba kutsogolo kwa unit. Mwa kukanikiza the 
batani mutha kusintha pakati pa AUTO / TSIKU LONSE / ON / OFF pa Zone 1
Bwerezani izi ku Zone 2 ndikukanikiza batani 
batani ndi Zone 3 mwa kukanikiza batani 
batani.
Kusintha makonda a pulogalamu
Tsitsani chophimba kutsogolo kwa unit.
Sunthani chosinthira chosankha kupita pamalo a PROG SET.
Tsopano mutha kupanga pulogalamu ya Zone 1.
Dinani pa or mabatani kuti musinthe P1 PA nthawi. Press
Dinani pa or mabatani kuti musinthe nthawi ya P1 OFF. Press
Bwerezani izi kuti musinthe ON & OFF nthawi za P2 & P3.
Press ndikubwereza zomwe zili pamwambapa kuti musinthe Zone 2.
Press ndikubwereza zomwe zili pamwambapa kuti musinthe Zone 3.
Mukamaliza, sunthani chosinthiracho kupita ku RUN malo.
Copy ntchito
Ntchito yokopera ingagwiritsidwe ntchito ngati wopanga mapulogalamu ali mu 7d mode.
Tsitsani chophimba kutsogolo kwa wopanga mapulogalamu.
Sunthani chosinthira chosankha kupita pamalo a PROG SET.
Khazikitsani nthawi ON & OFF za tsiku la sabata lomwe mukufuna kukopera.
Dinani pa 
batani kwa 2 secs. Tsiku lotsatira la sabata lidzayamba kung'anima.
Dinani pa batani kukopera ON & OFF mpaka lero.
Dinani pa batani kudumpha tsiku.
ON & OFF nthawi zitha kukopera masiku angapo pogwiritsa ntchito batani.
Dinani pa batani pamene kukopera kwatha.
Mukamaliza, sunthani chosinthiracho kupita ku RUN malo
Reviewkuyika zokonda za pulogalamu
Tsitsani chophimba kutsogolo kwa unit.
Sunthani chosinthira chosankha kupita pamalo a PROG SET.
Tsitsani chophimba kutsogolo kwa unit.
Sunthani chosinthira chosankha kupita pamalo a PROG SET.
Mwa kukanikiza izi zithaview nthawi iliyonse ya ON/OFF ya P1 mpaka P3 ya Zone 1.
Bwerezani ndondomekoyi kuti mubwerezeview nthawi ON/OFF za Zone 2 mwa kukanikiza ndiyeno kukanikiza
Bwerezani ndondomekoyi kuti mubwerezeview nthawi ON/OFF za Zone 3 mwa kukanikiza ndiyeno kukanikiza
Mukamaliza, sunthani chosinthiracho kupita ku RUN malo.
Limbikitsani ntchito
Ntchitoyi imalola wogwiritsa ntchito kuwonjezera nthawi ya ON kwa 1, 2 kapena 3 maola.
Ngati chigawo chomwe mukufuna kuti Boost chizimitsidwa, muli ndi mwayi woyatsa kwa maola 1, 2 kapena 3.
Dinani batani lofunika: 
za Zone 1, 
za Zone 2 ndi 
kwa Zone 3 kamodzi, kawiri kapena katatu motsatana.
Kuti muletse ntchito yolimbikitsa, ingodinani batani lowonjezera lomwe lilinso.
Ntchito yapatsogolo
Ntchitoyi imalola wogwiritsa ntchito kubweretsa patsogolo nthawi yosintha.
Ngati chigawocho chili ndi nthawi yoti ZIMAYI ndipo ADV ikanikizidwa, chigawocho chidzayatsidwa mpaka kumapeto kwa nthawi yosintha.
Ngati chigawocho chili ndi nthawi yoti ON ndipo ADV ikanikizidwa, chigawocho chidzazimitsidwa mpaka kumapeto kwa nthawi yosintha.
Press 
za Zone 1, 
za Zone 2 kapena 
za Zone 3.
Kuti muletse ntchito ya ADVANCE, ingodinaninso batani la ADV.
Njira yamaholide
Tsitsani chophimba kutsogolo kwa unit.
Sunthani chosinthira chosankha kupita pamalo a RUN.
Dinani pa 
batani.
Tsiku ndi nthawi yomwe ilipo zikuwonekera pazenera. Tsopano n’zotheka kulemba deti ndi nthawi imene mukukonzekera kubwerera.
Dinani pa or mabatani kuti musinthe nthawi ya tchuthi yofunikira.
Dinani pa batani.
Wopanga mapulogalamu tsopano wazimitsa masiku omwe asankhidwa.
Mwa kukanikiza the batani kachiwiri, izi ziletsa njira yatchuthi, potero kubwezera wopanga mapulogalamu ku zoikamo zanthawi zonse.
Kusankha kwamtundu wakumbuyo
On
Pali makonda awiri osankhidwa. Zokhazikitsira zokhazikika kufakitale ZINTHU ZOYANTHA.
ON Nyali yakumbuyo imayatsidwa kwamuyaya.
AUTO Mukadina batani lililonse nyali yakumbuyo imakhala masekondi 10.
Kuti musinthe mawonekedwe a backlight, tsitsani chivundikiro kutsogolo kwa unit.
Sunthani chosinthira chosankha kupita pamalo a RUN.
Dinani pa batani kwa 5 masekondi.
Dinani kapena or mabatani kuti musankhe ON kapena AUTO mode.
Dinani pa batani
Tsekani keypad ndikutsegula
Zotsegulidwa
Kuti mutseke makatani, dinani ndikugwira ndi mabatani 5 masekondi.
zidzawonekera pazenera. Makiyidi atsekedwa tsopano.
Kuti mutsegule keypad, dinani ndikugwira ndi mabatani 5 masekondi.
zidzazimiririka pazenera. Makiyiwo tsopano atsegulidwa.
Ntchito yoteteza chisanu
Osati
Mtundu wosankhidwa wa 5 ~ 20°C. Ntchitoyi imayikidwa kuti iteteze mapaipi kuti asaundane kapena kuteteza kutentha kwa chipinda chochepa pamene pulogalamuyo yakonzedwa kuti AYI AYI kapena WOZIMITSA pamanja.
Chitetezo cha chisanu chikhoza kutsegulidwa potsatira ndondomeko ili m'munsiyi.
Sunthani chosinthira chosankha kupita pamalo a RUN.
Dinani onse a ndi mabatani 5 masekondi, kulowa kusankha mumalowedwe.
Dinani kapena or mabatani kuti mutsegule kapena kuzimitsa chitetezo chachisanu.
Dinani pa batani kuti mutsimikizire.
Dinani kapena or mabatani kuti muwonjezere kapena kuchepetsa zomwe mukufuna
chitetezo cha chisanu.
Dinani pa batani kusankha.
Magawo onse awiri a MADZI OTSATIRA NDI AKUtentha adzayatsidwa ngati kutentha kwa chipinda kutsika pansi pa malo otetezedwa ndi chisanu.
Pamene chitetezo cha chisanu chayatsidwa "Frost" idzawonekera pazenera.
Chitetezo cha chisanu chikatsegulidwa "Frost" idzawunikira pazenera.
Kukonzanso kwakukulu
Tsitsani chophimba kutsogolo kwa wopanga mapulogalamu.
Pali mahinji anayi omwe akugwira chivundikirocho m'malo mwake.
Pakati pa 3 ndi 4 hinges pali dzenje lozungulira.
Lowetsani cholembera cha mpira kapena chinthu chofananira kuti mukhazikitsenso pulogalamuyo.
Mukadina batani lokhazikitsiranso master, tsiku ndi nthawi tsopano ziyenera kukonzedwanso.
EPH Imawongolera Ireland
technical@ephcontrols.com www.ephcontrols.com
EPH Amalamulira UK
technical@ephcontrols.co.uk www.ephcontrols.co.uk
20221107_R37_OpIns_PK
Zolemba / Zothandizira
 |
EPH AMALANGIZA R37 3 Zone Programmer [pdf] Buku Logwiritsa Ntchito R37 3 Zone Programmer, R37 3, Zone Programmer, Programmer |
 |
EPH AMALANGIZA R37 3 Zone Programmer [pdf] Kukhazikitsa Guide R37 3 Zone Programmer, R37 3, Zone Programmer, Programmer |
 |
EPH AMALANGIZA R37 3 Zone Programmer [pdf] Buku la Malangizo R37, R37 3 Zone Programmer, 3 Zone Programmer, Programmer |
 |
EPH AMALANGIZA R37 3 Zone Programmer [pdf] Kukhazikitsa Guide R37, R37 3 Zone Programmer, 3 Zone Programmer, Programmer |
