Mawu Oyamba
The Wampler Catacombs is a programmable, all-in-one delay and reverb pedal designed to provide a wide range of time-based effects for musicians. This manual provides essential information for setting up, operating, maintaining, and troubleshooting your Catacombs pedal.
Zathaview
The Catacombs pedal integrates 11 popular delay and reverb sounds into a single, intuitive unit. It features studio-quality 48 kHz sampling rate with 24-bit audio conversion, 8 onboard preset locations, and MIDI compatibility for up to 128 total presets.
Chithunzi 1: Patsogolo view wa Wampler Catacombs pedal, showing controls for delay and reverb effects, input/output jacks, and footswitches.
Chithunzi 2: Zopindika view wa Wampler Catacombs pedal, highlighting its compact design and various control knobs.
Khazikitsa
Zofunika Mphamvu
The Wampler Catacombs pedal requires a standard 9V DC power supply (not included) with a center-negative barrel connector. Ensure the power supply provides sufficient current for optimal performance.
Connecting Your Pedal
- Connect your instrument (e.g., guitar) to the MONO PA or STEREO MU jack on the right side of the pedal using a standard 1/4-inch instrument cable.
- Gwirizanitsani ndi MONO KUTULUKA or STEREO OUT jack on the left side of the pedal to your amplifier or next effect pedal.
- Connect the 9V DC power supply to the 9V DC jack input.
- For MIDI control, connect a MIDI cable to the MIDI kulowa.
Malangizo Ogwiritsira Ntchito
Amazilamuliraview
- Delay Type Knob: Selects between various delay types including Tape, SPC, FTE, BBD, ANLG, and DIGI.
- Reverb Type Knob: Selects between reverb types such as SHMR (Shimmer), PLT (Plate), SPR (Spring), ROOM, and HALL.
- Time/Shimmer Knob: Adjusts the delay time or shimmer intensity depending on the selected effect.
- Feedback/Decay Knob: Controls the number of delay repeats or the reverb decay time.
- Mod Rate Knob: Adjusts the modulation rate for effects with modulation.
- Delay Tone Knob: Shapes the tone of the delay repeats.
- Reverb Tone Knob: Shapes the tone of the reverb effect.
- Bypass/ALT Footswitch: Toggles the effect on/off. Hold to access alternate functions (ALT mode).
- Preset/Save Footswitch: Cycles through presets. Hold to save current settings to a preset location.
- Tap Tempo Footswitch: Taps in the desired delay tempo.
Kusunga ndi Kukumbukira Zokonzedweratu
The Catacombs pedal allows for 8 onboard preset locations. To save a preset, adjust the knobs to your desired sound, then press and hold the Preset/Save footswitch until the indicator lights confirm the save. To recall a preset, short press the Preset/Save footswitch to cycle through the saved locations.
Alternate Functions (ALT Mode)
Some knobs have alternate functions accessible by holding the Bypass/ALT footswitch. When in ALT mode, the indicator light will change (e.g., from blue to red as noted in some user feedback), allowing you to adjust secondary parameters. Release the footswitch to return to normal operation.
Kusamalira
To ensure the longevity and optimal performance of your Wampler Catacombs pedal, follow these maintenance guidelines:
- Keep the pedal clean by wiping it with a soft, dry cloth. Avoid abrasive cleaners or solvents.
- Sungani pedal pamalo ozizira komanso ouma, kutali ndi dzuwa lachindunji komanso kutentha kwambiri.
- Dulani magetsi ngati sakugwiritsidwa ntchito kwa nthawi yayitali.
- Regularly check all cable connections for secure fit.
Kusaka zolakwika
| Vuto | Chifukwa Chotheka | Yankho |
|---|---|---|
| Palibe phokoso pamene pedal ikugwiridwa. | Incorrect power supply, faulty cables, incorrect input/output connections. | Verify power supply is 9V DC center-negative. Check all instrument cables. Ensure input is connected to IN and output to OUT. |
| Effect is too subtle or too extreme. | Knobs are set incorrectly, or in ALT mode unintentionally. | Adjust the relevant control knobs (Time, Feedback, Tone). Check if the pedal is in ALT mode and adjust accordingly. |
| Cannot save or recall presets. | Incorrect footswitch operation. | Onetsetsani kuti mwagwira Preset/Save footswitch long enough to save. For recalling, use short presses. |
| Noise or hum. | Ground loop, faulty power supply, interference. | Use an isolated power supply. Try different cables. Ensure proper grounding of all equipment. |
Zofotokozera
- Chitsanzo: CATACOMBS
- Makulidwe: 7.25 x 5.7 x 3.75 mainchesi
- Kulemera kwa chinthu: 1.39 mapaundi
- Gwero la Mphamvu: Corded Electric (9V DC, center-negative, power supply not included)
- Mtundu wa Signal: Analogi
- Audio Output Effects: Kuchedwa, Reverb
- Sampling Mlingo: 48 kHz
- Audio Bit Depth: 24-bit
- Kukonzekera: 8 onboard, 128 via MIDI
- Manufacture Location: Designed and Built in the USA
Chitsimikizo ndi Thandizo
Wampler Pedals products are designed and built to high standards. For warranty information and technical support, please refer to the official Wampndi Pedals webtsamba kapena funsani makasitomala awo mwachindunji. Sungani umboni wanu wogula kuti mutenge chitsimikizo.
Kuti mudziwe zambiri, pitani ku Wampler Store on Amazon.