AiM K6 Remote Button Interface

Zofotokozera:

• Mabatani: K6 - 6 programmable, K8 - 8 programmable, K15 - 15 programmable
• Kumbuyo: RGB yokhala ndi Dimming njira
• Kulumikizana: AiM CAN kudzera pa 5 pini Binder 712 cholumikizira chachikazi
• Thupi Zofunika: Mpira wa silicon ndi kulimbikitsa PA6 GS30%
• Makulidwe: K6 - 97.4x71x4x24mm, K8 - 127.4×71.4x24mm, K15 - 157.4×104.4x24mm
• Kulemera kwake: K6 - 120g, K8 - 150g, K15 - 250g
• Zosalowa madzi: IP67

Malangizo Ogwiritsira Ntchito Zogulitsa

Kulumikiza Keypad:
Lumikizani Keypad ku AiM PDM08 kapena PDM32 pogwiritsa ntchito chingwe choperekedwa cha CAN. Onetsetsani kuti kulumikizana kotetezeka kwapangidwa.

Kupanga Mabatani:
Gwiritsani ntchito pulogalamu ya AiM RaceStudio 3 kuti musinthe batani lililonse pa Keypad malinga ndi zomwe mumakonda. Mabatani amatha kukhazikitsidwa ngati Momentary kapena Multi-Status.

 Kukhazikitsa Mabatani:

• Kanthawi: Gwirizanitsani lamulo ku batani lililonse. Pamafunika Kuwonetsera kwa PDM kasinthidwe.
• Zambiri: Amalola kuti mawonekedwe asinthe nthawi iliyonse ikakanikiza batani. Zothandiza posankha zokonda zosiyanasiyana.

 Kupanga Nthawi Yoyambira:
Mutha kufotokozera zikhalidwe zosiyanasiyana za batani lopukutira kutengera kutalika komwe likukanikizidwa. Yambitsani bokosi loyang'anira nthawi muzosankha kuti mukhazikitse izi.

Tsegulani Kagwiritsidwe Ntchito:
Ngati mukugwiritsa ntchito Keypad pakuyika kwa AiM popanda chida chachikulu, tsatirani njira zomwe zaperekedwa pofotokozera mitsinje ya CAN.

FAQ:

1. Kodi ndimatsitsa bwanji pulogalamu ya AiM RaceStudio3?
   Kuti mutsitse pulogalamuyi, pitani ku AiM website pa aim-sportline.com ndikuyenda kupita kumalo otsitsa a Software/Firmware.
2. Kodi ndingagule zingwe zotsalira za CAN za Keypad?
   Inde, zingwe zotsalira za CAN zitha kugulidwa padera. Onani manambala okhudzana nawo kuti muyitanitsa.
3. Kodi ndingayanjanitse momasuka mawonekedwe a ON ndi OFF ndi manambala? 
   Inde, mawonekedwe onse ON ndi OFF atha kulumikizidwa ndi manambala pokonza mabatani a Keypad.

Mawu Oyamba

• AiM Keypad ndi mtundu watsopano wa zowonjezera za AiM zotengera protocol ya CAN Bus yomwe imagwiritsidwa ntchito pa netiweki ya AiM; amatha kulumikizidwa ku AiM PDM08 kapena PDM32.
• Keypad imapezeka m'mitundu yosiyanasiyana malinga ndi kuchuluka kwa mabatani omwe amawonekera ndipo mawonekedwe ake amatumizidwa ku Network Master kudzera pa kulumikizana kwa AiM CAN.
• Mabatani onse amatha kusinthika kwathunthu pogwiritsa ntchito AiM RaceStudio 3 Software.

Batani lililonse likhoza kukhazikitsidwa motere:

• Kanthawi: Kankhani batani ali ON pamene kukankha batani kukankhidwa
• Sinthani: mawonekedwe a batani lokankhira amasintha kuchoka pa ON kupita ku OFF nthawi iliyonse mukankhira batani
• Maonekedwe angapo: mtengo wokankhira umasintha kuchoka pa 0 kupita ku MAX Value nthawi iliyonse ikakankhira batani.

Mutha kufotokozeranso nthawi yocheperako pa batani lililonse lomwe limatanthawuza machitidwe osiyanasiyana pomwe chochitika cha SHORT kapena LONG chikapezeka. Bulu lililonse lokankhira limatha kusinthidwa kukhala lamtundu wina kapena molimba, pang'onopang'ono, mwachangu kapena mothwanima. Keypad imagawana njira zonse zoyika zomwe zingagwiritsidwe ntchito - chifukwa cha mtundu wa LEDS - zonse kuvomereza chochitika cha kukanikiza batani kapena mawonekedwe a chipangizocho.

Pomaliza, ndizotheka kukonza batani lakukankhira kuti muwonjezere kapena kuchepetsa mulingo wowala wa keypad. ndi kutumiza malamulo ku chipangizo chachikulu. Gome ili m'munsili likuwonetsa mawonekedwe amitundu yomwe ilipo ya Keypad.

	K6	K8	k15
Mabatani	6 zokhazikika	8 zokhazikika	15 zokhazikika
Kuwala kwambuyo		RGB yokhala ndi Dimming njira
Kulumikizana	AiM CAN kudzera pa 5 pini Binder 712 cholumikizira chachikazi
Zofunika Zathupi	mphira silikoni ndi kulimbikitsa PA6 GS30%
Makulidwe	97.4x71x4x24mm	127.4×71.4×24	157.4×104.4×24
Kulemera	120g pa	150g pa	250g pa
Chosalowa madzi		IP67

Zida zomwe zilipo komanso zosinthira

Zida za Keypad zomwe zilipo ndi:

Katundu K6

Katundu K6

• Keypad K6+50 masentimita AiM CAN chingwe X08KPK6AC050
• Keypad K6+100 masentimita AiM CAN chingwe X08KPK6AC050
• Keypad K6+200 masentimita AiM CAN chingwe X08KPK6AC050
• Keypad K6+400 masentimita AiM CAN chingwe X08KPK6AC050

Katundu K8

• Keypad K8+50 masentimita AiM CAN chingwe X08KPK8AC050
• Keypad K8+100 masentimita AiM CAN chingwe X08KPK8AC100
• Keypad K8+200 masentimita AiM CAN chingwe X08KPK8AC200
• Keypad K8+400 masentimita AiM CAN chingwe X08KPK8AC400

Katundu K15

• Keypad K15+50 masentimita AiM CAN chingwe X08KPK15AC050
• Keypad K15+100 masentimita AiM CAN chingwe X08KPK15AC100
• Keypad K15+200 masentimita AiM CAN chingwe X08KPK15AC200
• Keypad K15+400 masentimita AiM CAN chingwe X08KPK15AC400

Ma Keypads onse amabwera ndi chingwe cha CAN chomwe chimagwiritsidwa ntchito kulumikiza ku chipangizo chachikulu koma zingwe zimathanso kugulidwa padera ngati zida zosinthira.

Nambala zofananira ndi izi:

• 50 masentimita AiM CAN chingwe V02554790
• 100 masentimita AiM CAN chingwe V02554810
• 200 masentimita AiM CAN chingwe V02554820
• 400 masentimita AiM CAN chingwe V02554830

Mabatani azithunzi:

• 72 zidutswa zithunzi X08KPK8KICONS
• chizindikiro chimodzi dinani apa kuti mudziwe gawo lililonse lachithunzichi

Kukonzekera mapulogalamu

• Kuti mukonze ma Keypads a AiM, chonde tsitsani pulogalamu ya AiM RaceStudio3 kuchokera ku AiM website pa aim-sportline.com Malo otsitsa mapulogalamu / firmware: AiM - Tsitsani mapulogalamu / Firmware (aim-sportline.com)

Mukayika pulogalamuyo, yesani ndikutsatira izi:

• Lowetsani Zosintha Zosintha podina chizindikiro chomwe chili pansipa:
• Dinani "Chatsopano" batani pamwamba kumanja kwa toolbar ndikusankha PDM yomwe mukufuna kukonza
• Pulogalamuyi imalowetsa PDM Configuration
• Lowetsani "CAN Expansions" tabu (1) ndikudina "Kukulitsa Kwatsopano" (2)
• Sankhani Keypad yomwe mukufuna (K8 mu example)
• Konzani izo

chonde dziwani: chipangizo chanu cham'mwamba chimatha kuyang'anira ma keypad opitilira 8.Kukonzekera kwa Pushbuttons 

Zolemba mwachangu tisanayambe kusanthula momwe mungasinthire ma Keypads a AiM:

• pushbutton udindo ukhoza kukhazikitsidwa ngati Momentary, Toggle kapena Multi-status monga tafotokozera ndime 3.1.1.; Ndikothekanso kukhazikitsa nthawi yoti muzitha kuwongolera batani lalifupi komanso lalitali m'njira zosiyanasiyana
• pushbutton imatumizidwa nthawi zonse kudzera mu basi ya AiM CAN
• udindo wa aliyense kankhani batani pa mphamvu OFF akhoza kubwezeretsedwa pa mphamvu zotsatirazi ON
• batani lililonse limatha kusinthidwa - lolimba kapena kuthwanima - mumitundu yosiyanasiyana 8 monga tafotokozera m'ndime 3.1.2
• ndizotheka kukonza batani lakukankhira kuti muwonjezere kapena kuchepetsa mulingo wowala wa LED
• kuyika batani lokankhira ngati Momentary mutha kugwirizanitsa lamulo ("Menyu lowani" ndi zina) ku batani lililonse.

Kusintha kwa mawonekedwe a Pushbuttons
Mutha kukhazikitsa mitundu yosiyanasiyana pa batani lililonse:

ZOCHITIKA. udindo ndi:

• ON pamene kukankhira batani
• ZIMALIRA pamene kukankhira batani kumasulidwa

Chonde dziwani: zonse ziwiri ON ndi OFF zitha kulumikizidwa momasuka ndi manambala.

Chonde dziwani: kungoyika batani lakankhira ngati Kanthawi, mutha kuphatikizira lamulo ku batani lililonse koma kuti mutero ndikofunikira kuti mudawonjezerapo Chiwonetsero ku kasinthidwe ka PDM.

Potengera chithunzi chomwe chili pansipa, kuti muwonjezere chiwonetsero pakusintha kwa PDM: 

• lowetsani tabu yowonetsera (1)
• gulu losankhidwa likufunsidwa kuti lisankhe lomwe muwonjezere (2)
• dinani "Chabwino" (3) ndikusankha mawonekedwe omwe mukufuna pagawo lomwe lafunsidwa

Malamulo omwe alipo ndi awa: 

• Sinthani tsamba lowonetsera:
  • Tsamba lotsatira lowonetsera
  • Tsamba lowonetsera lapitalo
• Onetsani batani:
  • Lowani menyu: kuti muyende pamenyu yowonetsera: mabatani anayi amafunikira; amasanduka oyera pamene ena ndi olumala. Chonde dziwani: mabatani ogwiritsidwa ntchito amasintha molingana ndi malo - opingasa kapena ofukula - a kiyibodi yanu, pachifukwa ichi kusankha malo ndikofunikira.
  • Lowani kukumbukira: lamulo ili likulowetsa kukumbukira deta yowonetsera pambuyo pa mayeso.
• Bwezeretsani ma alarm omwe mapeto awo ali batani ndikukanikiza.
• Bwezeretsani zowerengera:
  • Bwezerani ma odometer onse.
  • Bwezeretsani odometer "x" (malinga ndi kuchuluka kwa ma odometer omwe alipo)
• Kuwala kwa keypad
  • Kuwonjezeka
  • Kuchepetsa

TOGGLE, udindo ndi: 

• ON pamene batani akankhidwa kamodzi, ndipo amakhala ON mpaka anakankhira kachiwiri
• ZIMU pamene batani likankhidwa kachiwiri.

Chonde dziwani: zonse ziwiri ON ndi OFF zitha kulumikizidwa momasuka ndi manambala

ZOCHULUKA: mawonekedwe amatha kuganiza zamitundu yosiyanasiyana yomwe imasintha nthawi iliyonse ikankhira batani. Izi ndizothandiza, mwachitsanzoample, kusankha mamapu osiyanasiyana kapena kukhazikitsa milingo yoyimitsidwa yosiyana etc.

Ziribe kanthu momwe batani lakankhira likhazikitsidwa mungathenso kukhazikitsa nthawi yofikira: pamenepa, batani lakankhira limayikidwa pazikhalidwe ziwiri zosiyana zomwe mungafotokoze kutengera nthawi yomwe mukukankhira.

Kuti muchite izi, yambitsani bokosi la "kugwiritsa ntchito nthawi" pabokosi lapamwamba lamagulu oyika. Kusintha kwa mtundu wa Pushbutton
Batani lililonse limatha kukhazikitsidwa ndi mitundu yosiyanasiyana kuti liwonetse zomwe dalaivala achita ndi mayankho ake: batani lolowera litha kutembenuzidwa - mwachitsanzo.ample - kuphethira (pang'onopang'ono kapena mofulumira) CHOBIRIRA kusonyeza kuti chakankhidwa, ndi CHOBIRIRA cholimba pamene chochitikacho chatsegulidwa.

Ma keypad otsegula

Keypad amaperekedwanso mu mtundu wa "Open" womwe umakupatsani mwayi wofotokozera mitsinje ya CAN. Mtunduwu uyenera kugwiritsidwa ntchito ngati chida cha AiM master palibe, koma mutha kuchigwiritsa ntchito pakuyika kulikonse kwa AiM. Kuti muchite izi, muyenera kutsatira njira izi:

• khazikitsani Keypad ngati "yolumikizidwa ku chipangizo cha AiM"
• tumizani kasinthidwe
• tsegulani kasinthidwe ka AiM Chipangizo
• sankhani kukulitsa "Open" ndikusintha ngati Keypad K8.

Zojambula zaukadaulo

Zithunzi zotsatirazi zikuwonetsa miyeso ya AiM Keypads ndi pinout.

Keypad K6 miyeso mu mm [ mainchesi]

Keypad K6 pinoutKeypad K15 miyeso mu mm [ mainchesi]: Keypad K15 pinout: 

Zolemba / Zothandizira

AiM K6 Remote Button Interface [pdf] Buku Logwiritsa Ntchito K6, K8, K15, K6 Remote Button Interface, K6, Remote Button Interface, Button Interface, Interface

Maumboni

• Buku Logwiritsa Ntchito