AAON ASM08070 Motor Speed Controller
Zofotokozera
- Dzina lazogulitsa: Motor Speed Controller
- Voltage Zosankha: 240 V, 480 V
- Njira Yowongolera: Phase control method
- Mitundu Yagalimoto: Permanent split capacitor (PSC) or shaded pole
- Maulendo othamanga: Low and high speed
- Control Power Inputs: 24 VAC
LEMBO LA KUSINTHA DZINA LA PRODUCT
| KUSINTHA NDI TSIKU | SINTHA |
| Rev. C. November 4, 2025 | Updated part numbers |
| Rev. B, Okutobala 4, 2023 | Kusinthidwa gwero lamphamvu lamagetsi pamatebulo ofotokozera a 240V ndi 480V |
| Rev. A, Seputembara 16, 2021 | Choyambirira |
ZIGAWO ZA DZINA LA PRODUCT
| GAWO DESCRIPTION | GAWO NUMBER |
| Wowongolera Liwiro Lagalimoto (240 V) | ASM08070 |
| Wowongolera Liwiro Lagalimoto (480 V) | ASM08077 |
| Motor Speed Controller (240 V) (2024 and previous) | ASM02907 |
| Motor Speed Controller (480 V) (2024 and previous) | ASM02908 |
ZATHAVIEW
Zina zambiri
Zathaview
- The Motor Speed Controller idapangidwa kuti iziwongolera kuthamanga kwa ma alternating current (AC) induction motors muzowotcha mpweya.
- The Motor Speed Controller is used with blower motors with
- Hall effect tachometer sensors included to help facilitate blower speed control.
Mawonekedwe
There are two Motor Speed Controller options, the 240 V andthe 480 V. Both controllers function the same, but are equippedwith a different voltage power supply. See Figure 1, this page fordetails. The Motor Speed Controller controls speed based on thedip switch settings. The controller provides two speed modes,low and high speed. The two modes are controlled by 24 VAC control power inputs.
CHENJEZO: Wowongolera amagwiritsa ntchito njira yowongolera gawo kuti asinthe voltagamaperekedwa kwa motere. Tsimikizirani ndi wopanga galimoto kuti galimoto yomwe ikuyendetsedwa ndiyovomerezeka pakugwira ntchito kwamtunduwu. Mtundu wagalimoto uyenera kukhala wokhazikika wogawanika (PSC) kapena mlongoti wokhala ndi mthunzi ndipo ukhale ndi kugunda kumodzi pakusintha Hall effect tachometer sensor.
Chithunzi 1: Motor Speed Controller 240 V vs. 480 V
Dip Switch Zikhazikiko
M'mapulogalamu Awiri a Speed Speed, liwiro lotsika limayikidwa ndi kuchuluka kwa ma rpm pama switch onse omwe ali pamalo otseguka/ozimitsa. Onani Table 1, tsamba ili kuti mupeze zosintha za dip switch.
| Dip Sinthani | RPM |
| 1 | 20 |
| 2 | 40 |
| 3 | 80 |
| 4 | 160 |
| 5 | 320 |
| 6 | 640 |
| 7 | 1280 |
| 8 | 2560 |
Gulu 1: Dip Switch Zikhazikiko
ZINDIKIRANI: If the dip switch setting is outside of the 1000-3400 rpm range, it is invalid and the fan will run at 100%.
Dip Switch Zikhazikiko
Kuwerengera kwa Dip Switch
Kuti mudziwe liwiro lagalimoto, werengera kuchuluka kwa ma switch onse pamalo otseguka/ozimitsa. Za example, ngati kusintha 1 ,3 ,5, ndi 7 kutsegulidwa / kuzimitsa, liwiro la galimoto ndi 1700. Onani Chithunzi 1, tsamba ili kuti mudziwe zambiri.
Chithunzi 2: Motor Speed Controller Dip Switch Settings
Kukula kwa Motor Speed Controller
Chithunzi 3: Kukula kwa Motor Speed Controller
INSTALLATION NDI WRING
Wiring
Onani Table 2 ndi 3, tsamba ili la Motor Speed Controller 240 V ndi 480 V.
| Wowongolera liwiro la mota 240 V | |
| Kufotokozera | Mtengo |
| Logic Power Source | 18-30 VAC@3VA |
| Gwero la Mphamvu Yamagetsi | 204-254 VAC |
| Mphamvu AC pafupipafupi | 59-61 Hz |
| Mtengo Wamakono Wagalimoto | 4 A |
| Kugwirizana kwagalimoto | Permanent Split Capacitor kapena Shaded Pole |
| Nthawi Yoyambira Yonse Yothamanga | 15 masekondi |
| Malumikizidwe a Mphamvu | 1/4 "ma tabu olumikizana mwachangu |
| Maulalo Olowetsa Analog | Terminal Block, 14 GA Max |
| Tach Sensor Connections | 3-pini 0.1” MTA cholumikizira |
| Kuwongolera kwa Analogi (2-10V) | 1000-3400 RPM |
| Kutentha Kosungirako | -40ºC mpaka +85ºC |
| Kutentha kwa Ntchito | -40ºC mpaka +70ºC |
| UL Gulu | UL 60730-1, Zowongolera Zamagetsi Zamagetsi |
Gulu 2: Motor Speed Controller 240 V Specifications
CHENJEZO: Chotsani mphamvu zonse kwa wolamulira musanayambe kugwirizanitsa kapena kusintha kuti mupewe kugwedezeka kwa magetsi kapena kuwonongeka kwa unit.
| Wowongolera liwiro la mota 480 V | |
| Kufotokozera | Mtengo |
| Logic Power Source | 18-30 VAC@3VA |
| Gwero la Mphamvu Yamagetsi | 408-528 VAC |
| Mphamvu AC pafupipafupi | 59-61 Hz |
| Mtengo Wamakono Wagalimoto | 4 A |
| Kugwirizana kwagalimoto | Permanent Split Capacitor kapena Shaded Pole |
| Nthawi Yoyambira Yonse Yothamanga | 15 masekondi |
| Malumikizidwe a Mphamvu | 1/4 "ma tabu olumikizana mwachangu |
| Maulalo Olowetsa Analog | Terminal Block, 14 GA Max |
| Tach Sensor Connections | 3-pini 0.1” MTA cholumikizira |
| Kuwongolera kwa Analogi (2-10V) | 1000-3400 RPM |
| Kutentha Kosungirako | -40ºC mpaka +85ºC |
| Kutentha kwa Ntchito | -40ºC mpaka +70ºC |
| UL Gulu | UL 60730-1, Automatic Electrical Controls |
Gulu 3: Motor Speed Controller 480 V Specifications
Control Mphamvu
- There are three 1/4 inch quick-connect tabs for 24 VAC control power signal connections. The W1 terminal is 24 VAC common and ground.
- The W2 terminal is the high-speed input, and terminal W3 is the low speed input.
- If W2 is supplied with 24 VAC power and W3 is unpowered, the motor is will run at full speed.
- If W2 and W3 receive power, or if W3 receives power while W2 is unpowered, the motor speed will be controlled to the analog input voltage kapena dip switch setting.
Kulumikizana kwa Line ndi Magalimoto
- Malo olumikizira mwachangu a L1 ndi L2 akuyenera kulumikizidwa ndi magetsi a 240 V kapena 480 V. Ma terminal a M1 ndi M2 ayenera kulumikizidwa ndi injini.
Kukwera
- The Motor Speed Controller has a factory-mounted aluminum base plate. The metal base plate helps the controller regulate temperature and facilitate proper heat dissipation.
Ma Wiring Awiri Othamanga
- In Two Speed Mode, when 24 VAC power is applied only to terminal W2, the motor will operate at high speed.
- If 24 VAC power is applied to terminal W3 (instead of, or in addition to, terminal W2), the motor will operate at a speed determined by the dip switch setting. See Figure 4, this page for wiring details.
Chithunzi 4: Ma Wiring Awiri Othamanga
Zolowetsa ndi Zotuluka
I/O Mapu
Onani Table 4, tsamba ili pazolowetsa ndi zotuluka za Motor Speed Control.
| Motor Speed Controller | |
| Zolowetsa | |
| W1 | Ground (ya 24 VAC control voltage) |
| J1 | Ndemanga za fan tachometer |
| L1 | Mzere voltage (240 VAC kapena 480 VAC) |
| L2 | Mzere voltage (240 VAC kapena 480 VAC) |
| Zolowetsa za binary | |
| W2 | Kuthamanga kwambiri kwa fan (24 VAC) |
| W3 | Kuthamanga kwa fan (24 VAC) |
| Zotsatira za Analog | |
| Mtengo wa TB1 | 2-10 VDC yosintha liwiro la fan |
| Zotsatira | |
| M1 | Fani yamagalimoto |
| M2 | Fani yamagalimoto |
Gulu 4: Zolowetsa ndi Zotuluka
NTHAWI YA NTCHITO
Njira Zogwirira Ntchito
- Ntchito
- The Motor Speed Controller is used to control the speed of PSC or shaded-pole fan motors. The binary inputs are used to switch between High and Low Speed Modes. In High Speed Mode, the fan operates at 100%.
- In Low Speed Mode, the fan is controlled by the rpm setpoint determined by the dip switch setting. Fan speed is provided to the controller by a Hall effect tachometer in the motor. If the fan speed is above or below setpoint, the voltage yoperekedwa kwa fani idzachepetsedwa kapena kuwonjezeredwa kuti asunge liwiro la fan.
- Kutuluka Kwadongosolo
- Mu Off Mode, mulibe W2 kapena W3 yolowera ndipo zotulutsa za fan zimachotsedwa mphamvu.
- High Speed Mode
- Mu High Speed Mode, kulowetsa kwa W2 kumalimbikitsidwa ndi 24 VAC mphamvu ndipo kulowetsa kwa W3 kumakhala kopanda mphamvu. Chokupizacho chimathamanga kwambiri. Ngati zolowetsa za W2 ndi W3 zonse zili zopanda mphamvu, zotulutsa za fan sizikhala ndi mphamvu. Ngati kulowetsa kwa W3 kuli ndi mphamvu 24 VAC, zimakupiza zimasinthira ku liwiro lotsika.
- Low Speed Mode
- Mu Low Speed Mode, zimakupiza zimagwira ntchito pomwe W3 alowetsamo mphamvu kapena pomwe zolowetsa za W2 ndi W3 zipatsidwa mphamvu ndi 24 VAC mphamvu.
- Faniyo ikayatsidwa, imathamanga kwambiri kwa masekondi 15 isanasinthe kupita ku liwiro lotsika.
- Kuthamanga kwa fan kudzasungidwa pa liwiro lodziwika ndi dip switch switch.
- Mu Mayendedwe Awiri Othamanga, ma fan rpms amalembedwa pa board board. Malo osinthira akuyenera kuyimitsidwa kuti ZIMAYI kuti muwonjezere mtengo wa rpm wa malowo. Za example, for 2560 rpm, positions 1-7 should be set to ON and position 8 should be set to OFF.
- Ngati kulowetsa kwa W3 kulibe mphamvu, zimakupiza zimasinthira ku ntchito yothamanga kwambiri.
- Kutulutsa kwa fan kudzachepetsa mphamvu ngati zolowetsa zonse za W2 ndi W3 sizikhala ndi mphamvu.
ZAMBIRI ZAMALUMIKIZIDWE
- AAON Controls Support: 866-918-1100
- Lolemba mpaka Lachisanu, 7:00 AM mpaka 5:00 PM
- Central Standard Time
- Amawongolera Thandizo webtsamba:
- www.aaon.com/controlstechsupport
- AAON Factory Technical Support: 918-382-6450 techsupport@aaon.com
- ZINDIKIRANI: Musanayimbe Thandizo laukadaulo, chonde khalani ndi mtundu ndi nambala ya seriyo yagawo yomwe ilipo.
- Magawo: Pazigawo zolowa m'malo, chonde lemberani Woimira AAON wakudera lanu.
- 2425 South Yukon Ave
- Tulsa, OK
- 74107-2728
- Ph: 918-583-2266
- Fax: 918-583-6094
- AAON P/N: G097900, Rev. C
- Zasindikizidwa ku USA
- Copyright Novembala 2025
- Maumwini onse ndi otetezedwa
FAQs
Q: How do I confirm if my motor is compatible with the Motor Speed Controller?
A: Consult the motor manufacturer to verify if your motor is a permanent split capacitor (PSC) or shaded pole type with a Hall effect tachometer sensor.
Q: What should I do if the fan runs at 100% speed?
A: Check the dip switch settings and ensure they are within the valid RPM range of 1000-3400. Adjust as needed to set the desired speed.
Zolemba / Zothandizira
 |
AAON ASM08070 Motor Speed Controller [pdf] Kukhazikitsa Guide ASM08070, ASM08070 Motor Speed Controller, Motor Speed Controller, Speed Controller |