XTM PLU628706 120W Folding Solar Blanket Instruction Manual

120W FOLDING
SOLAR BLANKET

_________________________________
+ OWNERS/INSTRUCTION MANUAL
_________________________________

Please ensure that you have read the product manual and instruction in full prior to use. Failure to do so may result in incorrect operation and therefore impact on the products performance.

CHITETEZO / CHENJEZO

• Before using the XTM solar blanket ensure the instructions have been read and understood.
• The solar blanket is not intended for use by young children or infirm persons. Please keep away from pets.
• XTM solar blanket is designed to charge most 12 volt battery types including: Flooded(Lead acid), Gel, Sealed/Mat(AGM) and VRSLA batteries.
• Nthawi zonse muzivala Zida Zakutetezani Zanu (PPE) mukamagwira ntchito pafupi ndi mabatire. Izi zikuphatikiza magolovesi ndi chitetezo chamaso.
• Onetsetsani kuti batri ikulipidwa pamalo opumira mpweya wabwino. Mpweya wophulika umatha kutuluka mu batriyo mukamayendetsa. Osalipira batire pamalo otsekedwa kapena m'malo opanda mpweya.
• Osasuta konse, gwiritsani ntchito lawi lotseguka kapena kupanga ma sparks pafupi ndi batri kapena charger mukamayatsa ngati mpweya ungayambitse kuphulika. Chonde pitirizani kuyatsa ndudu, malawi amoto kapena zinthu zina zoyatsira kutali ndi batiri loyimbira nthawi zonse.
• XTM Solar blanket is not water resistant or waterproof. Do not expose the solar blanket to water or liquids.
• Do NOT attempt to use the solar blanket if the cables or plugs are damaged. These units do not contain serviceable parts. To avoid a hazard ensure that any damage to the unit. cable or plugs are replaced by a qualified technician.
• Do NOT disassemble the solar blanket. The warranty will be void if this instruction is ignored.
• If battery is still connected in the vehicle, ensure vehicle ignition is switched oft before charging the battery.
• Do NOT place the solar blanket on fabric/leather/vinyl seats.on the battery or balanced in the engine bay.
• Never charge a frozen battery, non-rechargeable or dry cell battery. A compatible solar controller is required to charge lithium battery. The included controller is not suitable for lithium battery.
• Do NOT bend or scratch solar blanket.
• Do NOT walk, sit or place heavy items onto the solar blankets or the kit in the bag.
• Do NOT use a high pressure hose to clean the solar blanket. Use a clean microfiber cloth to clean solar blanket surfaces.

XTM 10A MPPT SOLAR CHARGE CONTROLLER

• OSA disassemblele kapena kuyesa kukonza woyang'anira.
• Kulumikiza kwamagetsi kuyenera kukhalabe kolimba kuti tipewe kutentha kwambiri kuchokera kulumikizano lotayirira.
• Only charge 12V batteries that comply with the parameters of the controller.
• Kulumikizana kwa batri kumatha kulumikizidwa ku batri imodzi kapena kubanki ya mabatire.
• Keep in a dry well-ventilated area.

ZOFUNIKA KWAMBIRI!

*If load wires are not used it is recommended that these wires are covered
(1) Connection of components to the controller MUST be completed in the sequence outlined in the following Wiring diagram, paying particular attention to the “+” and ”-” wiring. When disconnecting components, the order is reversed.
(2) After turning the controller on, check that the LED indicator is green (if not green, please refer to section 8. Troubleshooting).

• Katundu wodziyesa ntchito

Load self-test function – the load will show as on when the controller is switched on.

Chithunzi cha Wiring

FIRST AID & BATTERIES

• For advice, contact the Poisons Information Centre in Australia (PH:13 11 26).
• Ngati batri acid imalumikizana ndi khungu kapena chovala, sambani nthawi yomweyo ndi sopo.
• Ngati batri asidi imalumikizana ndi maso, gwirani zikope ndikutulutsa diso mosalekeza ndi madzi oyenda kwa mphindi 15 kapena mpaka pomwe chidziwitso cha Poison chikukulangizani kuti muime.
• If battery acid is swallowed, do not induce vomiting. Drink a glass of water and immediately seek medical assistance.

KUCHITA:

ZOPHUNZITSA ZA DZUWA	High Efficiency Monocrystalline
MPHAMVU YA MPHAMVU	120 Watt Max @ 20.50V
TESTING CONDITION	AM1.5, 1000W/m², 25°C
KULIMBITSA TEMPERATURE	-40 ° C mpaka + 85 ° C
ZOTHANDIZA	5m extension lead with 50A connectors
90cm extension lead with 50A connector and alligator clips
10A 12V IP68 Dustproof and waterproof MPPT controller Suitable for Deep Cycle, GEL, AGM, VRSLA and Flooded batteries
ZOKHUDZA (mm)	375 (L) x 370 (W) x 40 (H) (folded)
1315 (L) x 760 (W) x 4 (H) (open)

Chenjezo:

• KUKHALA use and store the product in a dry and well ventilated location.
• OSA use near flammable liquids or explosives.
• IMANI use immediately if any wires become loose or electronic components are exposed.
• OSA hang solar blanket by corded loops, loops are designed to secure blanket to flat or angled surface only. They are not designed to hang the blanket vertically.

Momwe Mungagwiritsire Ntchito:

• Unfold the solar blanket.
• Place the solar blanket in a position directly facing the sun. Shadows will reduce optimum power output.
• Tilt the solar blanket at a suitable angle. (Additional support may be necessary)

1. BWINO
2. CHABWINO
3. ZOSAVUTA

• Connect the solar blanket to the controller and connect the battery clamp wire to the controller.

1. The below data is the amount of electricity this solar charger can generate under full sun, and ideal working conditions.

QUANTITY	TOTAL SOLAR OUTPUT (WATT)	KULIMBITSA PANO (AMP)	CHARGE CONTROLLER INCLUDED
Chigawo cha 1	120 Watt	5.86A	10A / 12V

2. The solar blanket generates electricity in proportion to the amount of sunlight exposed to the solar panels. The peak generation of power is on a clear day when the sun is at a correct angle toward the solar panels. Cloud cover, seasonal variations, incidental shading and dust and dirt on the solar blanket could decrease the performance of the solar charger.

3. Power loss during transmission through lead wire and connector, efficiency of charge controller and inverter will also decrease the amount of electricity you can generate.

• Do not pick the solar blanket up directly by the solar cells.
• Use the gap between the solar cells to pick the blanket up as illustrated below:

Do NOT stand or walk on the solar blanket.

CHARGING A 12V BATTERY

First connect battery to solar charge controller.
Second connect load to solar charge controller.
Finally connect solar blanket to solar charge controller.
ZINDIKIRANI: Heavy loads should be connected to the battery directly.

XTM 10A MPPT SOLAR CHARGE CONTROLLER

1. DZIWANI ZA CHITETEZO

• Werengani malangizo onse m'bukuli musanayike.
• DO NOT disassemble or attempt to repair the controller.
• Do disconnect the solar module before installing or moving the controller.
• Kulumikiza kwamagetsi kuyenera kukhalabe kolimba kuti tipewe kutentha kwambiri kuchokera kulumikizano lotayirira.
• Ingoyitanitsa mabatire omwe amagwirizana ndi zowongolera.
• Kulumikizana kwa batri kumatha kulumikizidwa ku batri imodzi kapena kubanki ya mabatire.
• Risk of electric shock due to the high voltages produced, from the photovoltaic (PV) and load when controller is in use.

2 POPANDAVIEW

The XTM 10A MPPT Solar Charge Controller adapts to the Maximum Power Point Tracking (MPPT) charging method. This enables the systems charging and discharging management to obtain the most radical optimisation, increases system flexibility and reduces overall system running cost. This controller supports a variety of battery types, including sealed, gel & flooded batteries. It can also be used around the home in many applications, such as home solar systems, solar lighting & garden lamps.

Mawonekedwe:

• Advanced Maximum Power Point Tracking (MPPT) technology
• Long lifespan design, made from high quality components within an aluminium housing
• Ultra-fast tracking speed & efficiency
• Accurately recognises & tracks multiple power points
• Photovoltaic (PV) power limitation function

3. ZOFUNIKA KWAMBIRI

(1)	Kulipiritsa Status LED chizindikiro	(4)	Mawaya Opanda Battery Ndi Oipa
(2)	Chizindikiro cha Battery Status LED	(5)	Katundu Mawaya Abwino ndi Oipa
(3)	PV Positive ndi Negative Waya	(6)	Kapu yamadzi

ZINDIKIRANI:

1. The waterproof cap must be fitted to prevent water & dust entering the unit.
2. COM adapter not available with this unit

4. KULUMIKIZANA

ZOFUNIKA KWAMBIRI!

*If load wires are not used it is recommended that these wires are covered.
(1) Connection of components to the controller MUST be completed in the sequence outlined in the following Wiring diagram, paying particular attention to the “+” and “-” wiring. When disconnecting components, the order is reversed.
(2) After turning the controller on, check that the LED indicator is green (if not green, please refer to section 8. Troubleshooting).

• Katundu wodziyesa ntchito

Load self-test function – the load will show as “on” when the controller is switched on.

Chithunzi cha Wiring

5. ZIZINDIKIRO ZA LED

chizindikiro	mtundu	kachirombo	Malangizo
	Green	Pa Solid	Photovoltaic (PV) connection normal but low voltage (radiance) kuchokera ku PV, osalipira
Green	Off	Palibe mphamvu ya PVtage (nthawi yausiku) kapena vuto la kulumikizana kwa PV
Green	Pang'onopang'ono Kuthwanima (1 kung'anima pa sekondi iliyonse)	kulipiritsa
Green	Kuthamanga Kofulumira (Kuwala 4 pa sekondi iliyonse)	Mtengo wa PVtage
	Green	Pa Solid	Normal
Green	Pang'onopang'ono Kuthwanima (1 kung'anima pa sekondi iliyonse)	Full
Green	Kuthamanga Kofulumira (Kuwala 4 pa sekondi iliyonse)	Pa voltage
lalanje	Pa Solid	Pansi pa voltage
Red	Pa Solid	Zatulutsidwa
Red	Kuthamanga Kofulumira (Kuwala 4 pa sekondi iliyonse)	Kutentha kwa Battery
Charging (green) and battery indicator (orange) flashing simultaneously	Dongosolo voltagndi cholakwika

6. LOAD WORKING MODE

Note: The controller’s ‘ON’ status indicator, is defaulted to show Load.

7. INBUILT CONTROLLER PROTECTIONS

Photovoltaic (PV) Protections:

• PV Pakali pano

Where PV over current occurs, battery charging will be limited to the maximum battery current rating. Oversized solar arrays will therefore not operate at peak power.

• PV Short Circuit

Where PV short circuit occurs, or PV input short circuits on low power, charging will stop, the controller will turn off and the LED indicator will not illuminate. Disconnect PV input from controller and check for short circuit in the wiring and reconnect.
Chenjezo: Damage to the controller may occur where PV input short circuits on high power.

• PV Zosintha Polarity

Where reverse polarity occurs, check the wire connections and resume normal operation.
Chenjezo: If this controller is connected to a different PV to the one supplied and the power from that solar panel (PV) is greater than 195W/12V(390W/24V) damage WILL occur to controller.

Chitetezo cha Battery:

• Bweretsani Polarity

Where battery reverse polarity occurs, check wire connections and resume normal operation.

• Pa Voltagndi (16V)

Where over voltage is detected, the controller will stop charging the battery, to prevent damage to the battery. Refer to section 9 Technical specifications.

• Over Discharge (11.1V)

Where over discharge (low voltage) is detected, the controller will stop power supply to load, to prevent damage to the battery. Refer to section 9 Technical specifications.

• Kutentha kwambiri

The controller monitors environmental temperature via a sensor. Where environmental temperatures exceed 65°C, the controller will cease charging until the temperature reaches 55°C, after which charging will resume.

• Cholakwika SENSOR Kutentha

If temperature sensor faults, the controller will continue to charge/discharge battery at the default temperature of 25°C, to prevent damage to the battery from overcharging & low voltage.

• Katundu Wambiri

The controller will disconnect the load where the load current exceeds the maximum load current rating of 1.05 times (10.5 amps). Where overload does occur, reduce load demand and restart controller.

• Kwezani Short Circuit

The controller will disconnect the load if short circuit (greater than or equal to 40 amps) occurs and will attempt reconnection 5 times. If reconnection attempts fail, the user must clear short circuit by disconnecting the controller from the circuit, check all the wiring for the short circuit and reconnect the controller (follow the steps outlined on the front of the controller) to reset. If restart fails, please refer to 8. Troubleshooting.

8. KUTSANTHA

Zolakwika	Zifukwa zotheka	Action
LED charging indicator turns off in daylight, despite PV modules under direct sun.	Photovoltaic(PV) array disconnection	Check PV & battery wire connections are correct and tight.
Palibe chizindikiro cha LED	Mphamvu ya batritage akhoza kukhala osachepera 8.5V	Yezerani mphamvu ya batritage with a multi-meter. A minimum of 8.5V are required to power the controller.
Battery LED indicator – fast flashing – green	Battery kuposa voltage	Onani ngati batire voltage is higher than the over voltage disconnect and disconnect the PV
Chizindikiro cha batri cha LED chofiira	Battery pa akatulutsidwa	Batire voltage imabwezeretsedwa kapena pamwamba pa LVR point (low voltagndi reconnect voltage), katundu adzachira
Chizindikiro cha batri cha LED chikuyaka	Kutentha kwa Battery	The controller will automatically turn off until temperature falls below 55 °C, then resume normal operation.
Load output has stopped	Load Overload ∧	(1) Reduce output load demand (2) Restart controller.
Load Short Circuit ∧	(1) Check load connections, clear controller fault. (2) Restart controller.

∧ Where overload or short circuit occurs and the controller ceases charging, it will then attempt auto-recovery 5 times, in the following timing intervals: 5s, 10s, 15s, 20s and 25s.

9. ZINTHU ZOPHUNZITSIRA

lachitsanzo katunduyo	Chithunzi cha Tracer2606BP
Dzinalo dongosolo voltage	12 / 24VDC Magalimoto
Adavotera / kutulutsa kwapano	10A
Adavoteledwa mphamvu	130W/12V; 260W / 24V
Asidi otsogolera	Pa Voltage Chotsani Voltage	Sealed/Gel/Flooded: 16V
Kutsika Voltagndi Reconnect Voltage	Sealed/Gel/Flooded: 12.6V
Kutsika Voltage Chotsani Voltage	Sealed/Gel/Flooded: 11.1V
Kutsekedwa	IP68 dust & waterproof
Ogwiritsa dzenje kukula	Φ3.5mm

10. KUDZIPEREKA

Under the following conditions, product warranty does not cover/apply:

• Damage caused through misuse, including use within unsuitable environments.
• Damage caused as a result of PV, load current, voltage or power exceeding the rated value of the controller.
• Damage caused from use in excessively hot environments.
• If the controller has been disassembled, opened or altered by the user
• Damage caused from natural elements, for example lightning.
• Damage caused during transportation by the user.

MAFUNSO OFUNIKA KWAMBIRI

CHIKONDI

Zogulitsa zathu ndizotsimikizika kuti sizikhala zopanda zopanga zabwino komanso zopanga kwa miyezi 12.

Ngati malonda anu akhala olakwika panthawiyi, a SRGS PTY LTD angakupatseni mwayi wolowa nawo m'malo, ngongole kapena kubweza komwe chinthu chalakwika; kufotokozedwa molakwika; zosiyana ndi sampNdakuwonetsani kapena musachite zomwe akuyenera kuchita.

Chitsimikizo ichi sichikuphimba zinthu zosinthidwa kwambiri; kugwiritsa ntchito molakwika kapena kugwiritsa ntchito molakwika mankhwalawa mosemphana ndi malangizo a ogwiritsa ntchito kapena zolemba; kusintha kwa malingaliro ndi kufooka kwanthawi zonse.

Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and for compensation for any other reason-ably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and failure does not amount to a major failure.

Kuti mutenge chitsimikizo, tengerani malondawo kutsogolo kwa Service Desk ya sitolo yanu yapafupi yogula. Muyenera kuwonetsa risiti kapena umboni wina wogula. Zambiri zitha kufunidwa kuti mukwaniritse zomwe mukufuna. Ngati simungathe kupereka umboni wogula ndi risiti kapena sitetimenti yaku banki, chizindikiritso chosonyeza dzina, adilesi ndi siginecha chingafunike kuti mukwaniritse zomwe mukufuna.

Zowonongera zilizonse zokhudzana ndi kubwezera katundu wanu kusitolo nthawi zambiri zimayenera kulipidwa ndi inu. Pakugula masitolo paintaneti, SRGS PTY LTD idzalipira katundu wobwezera chinthu chilichonse chomwe chayesedwa kuti sichili bwino kwenikweni.

Ubwino kwa kasitomala woperekedwa ndi chitsimikizo ichi ndiwowonjezera pa maufulu ena ndi zithandizo zamalamulo aogula ku Australia zokhudzana ndi katundu kapena ntchito zomwe chitsimikizo ichi chikukhudzana.

Chitsimikizochi chikuperekedwa ndi SRGS PTY LTD, 6 Coulthards Avenue, Strathpine QLD 4500, Australia.
Foni: 1300 880 764.

Pulogalamu	628706
yomanga	Makanema a dzuwa a Monocrystalline
Max power (Nom.)	120W
Makulidwe (opindika)	375x370x40mm
Makulidwe (otseguka)	1315x760x4mm
Mphamvu ya Max voltage	20.5V
Max mphamvu panopa	5.86A
Tsegulani dera voltage	24.19V
Short dera panopa	6.43A
Kuleza Mphamvu	± 3%
Kutalika kwa waya	5+0.9 Metre
kutentha opaleshoni	-40 ° C mpaka + 85 ° C
Mikhalidwe yoyeserera	AM1.5 1000W/m² 25°C
Opangidwa mkati	China

PLU: 628706    CODE: 120WBLANKET
Manufactured & packaged for
Malingaliro a kampani SRGS PTY LTD
ABN 23 113 230 050
6 Coulthards Avenue
Strathpine OLD 4500, Australia
CHOPANGIDWA KU CHINA

Zolemba / Zothandizira

XTM PLU628706 120W Folding Solar Blanket [pdf] Buku la Malangizo PLU628706 120W Folding Solar Blanket, PLU628706, 120W Folding Solar Blanket, Folding Solar Blanket, Solar Blanket, Blanket