Panasonic ET-MDNHM10 Interface Board
* The illustration above is an example. In this manual, illustrations of ET-MDNHM10 are used as an example unless otherwise specifi ed.
Werengani musanagwiritse ntchito
The “Operating Instructions” explains about the interface boards to be installed to a Panasonic Connect Co., Ltd. display device (projector or fl at panel display). For Model No. and model names, refer to the product list (x page 4).
Zikomo pogula izi za Panasonic.
- Before using this product, please read these “Operating Instructions” and the “Operating Instructions” of the display device carefully and save the manuals for future use.
- Before using this product, be sure to read “Read this fi rst!” (x page 3).
Zogulitsa
- Mawu oti HDMI ndi HDMI High-Definition Multimedia Interface, ndi HDMI Logo ndizizindikiro kapena zizindikilo zolembetsedwa za HDMI Licensing Administrator, Inc. ku United States ndi mayiko ena.
Werengani izi kaye!
Chenjezo:
- Do not spill water on this product or allow this product to get wet. Doing so may cause fire, electric shock, or malfunction due to short circuit or overheating.
- Do not place a container with liquid close to this product.
- Consult your dealer when liquid such as water is spilled on this product.
- Do not place the supplied screws in a location that a child can reach. Accidentally swallowing them can cause a physical harm.
Seek a medical advice immediately if a child might have swallowed a screw. - Osasokoneza kapena kusintha.
Doing so may cause electric shock or fire. It may also cause a malfunction. - Ask the qualified technician or your dealer to install or remove this product to/from the flat panel display.
Failure to do so may cause electric shock. It may also cause a malfunction. - Turn off the power and disconnect the power plug from the outlet when installing or removing this product to/from the flat panel display.
Kulephera kutero kumatha kuyambitsa magetsi.
Chenjezo
- Do not place this product in a location with excessive humidity or dust, or in a location exposed to oil smoke or steam.
Kuchita izi kungayambitse moto kapena magetsi. - Do not place this product in extremely hot location.
Doing so may deteriorate the part, or may cause fire. - Do not install or store in a location with direct sunlight or close to the heating device, etc.
- Turn off the power and disconnect the power plug from the outlet when installing or removing this product to/from the projector.
Kulephera kutero kumatha kuyambitsa magetsi.
Njira zopewera kugwiritsa ntchito
Mndandanda wazinthu
The product names and their Model Nos. described in this document are as follows.
| dzina mankhwala | Product Model No. | ndemanga |
| Interface Board for HDMI 2 input | Kupanga-MDNHM10 | An Interface Board equipped with 2 HDMI inputs. |
| Interface Board for DVI-D 2 input | Kupanga-MDNDV10 | An Interface Board equipped with 2 DVI-D inputs. |
Supported display device
The display device (projector or flat panel display) supported by the Interface Board described in this document is as follows. (As of March 2019)
| purojekitala | PT-RQ13K, PT-RQ32K, PT-RQ22K |
| Flat panel display | (Support to be determined) |
Zindikirani
The model not described in the table may also be supported. Refer to the Operating Instructions of your display device.
About the handling of the product
- Do not touch the connector section of the Interface Board directly with your hands.
The component may be damaged by the static electricity. Handle this product after removing the static in your body by touching the surrounding metal, etc. - Ask a qualified technician to install or remove to/from the flat panel display.
There is a danger of electric shock or a malfunction may occur due to static electricity. Consult your dealer.
Njira zopewera kugwiritsa ntchito
Kutaya
To dispose of the product, ask your local authorities or dealer for correct methods of disposal.
Chalk
Make sure that the following accessories are provided with your product. Numbers enclosed in < > show the number of accessories.
Screw <4>
(XSB3+8FN)
chisamaliro
- Appropriately discard the packaging material after unpacking the product.
- For missing accessories, consult your dealer.
- Sungani tizigawo ting'onoting'ono m'njira yoyenera, ndipo sungani ndi ana ang'onoang'ono.
Zindikirani
- The supplied screws are spare. Use them when a screw to fix the slot cover of the display device is lost.
- The model numbers of accessories are subject to change without prior notice.
Maina a magawo ndi ntchito
Interface Board for HDMI 2 input (Model No.: ET-MDNHM10)
- <HDMI IN 1> terminal (when installed in <SLOT 1> of the display device), <HDMI IN 3> terminal (when installed in <SLOT 2> of the display device) This is a terminal to input the HDMI signal.
- <HDMI IN 2> terminal (when installed in <SLOT 1> of the display device), <HDMI IN 4> terminal (when installed in <SLOT 2> of the display device) This is a terminal to input the HDMI signal.
- Sungani
Installing the Interface Board
interface Board for DVI-D 2 input (Model No.: ET-MDNDV10)
- <DVI-D IN 1> terminal (when installed in <SLOT 1> of the display device), <DVI-D IN 3> terminal (when installed in <SLOT 2> of the display device) This is a terminal to input the DVI-D signal.
- <DVI-D IN 2> terminal (when installed in <SLOT 1> of the display device), <DVI-D IN 4> terminal (when installed in <SLOT 2> of the display device) This is a terminal to input the DVI-D signal.
- Sungani
Installing the Interface Board
It is recommended to ask a qualified technician to install or remove the Interface Board to a projector. A malfunction may occur due to static electricity. Consult your dealer.
Ask a qualified technician to install or remove the Interface Board to/from a flat panel display. There is a danger of electric shock or a malfunction may occur due to static electricity. Consult your dealer.
Before installing or removing the Interface Board
- Always turn off the power of the display device (projector or flat panel display) before installing or removing the Interface Board.
- Make sure to follow the procedure described in the Operating Instructions of your display device when turning off the power.
- Do not touch the connector section of the Interface Board directly with your hands.
The component may be damaged by the static electricity. - Remove the static charge from your body by touching the surrounding metal, etc., in advance to prevent the static electricity damage.
- Take care not to get injured when installing or removing the Interface Board.
Hands may be injured by the opening of the blank slot of the display device or the edge of the bracket of the Interface Board. - When installing the Interface Board to the slot, insert it into the connector straight and slowly.
It may not operate or cause malfunction if it is not correctly installed. - The figure indicating the installation and removal of the Interface Board is using the combination of the Interface Board for HDMI 2 input (Model No.: ET-MDNHM10) and the optional projector (Model No.: PT-RQ13K) as an example. Illustration of this document may vary from the actual product.
- The details of the installation or removal may be different depending on the display device, so confirm the Operating Instructions of your display device too.
How to install the Interface Board
- Remove the slot cover. (Fig. 1)
- Remove the four screws fixing the slot cover of the display by rotating counterclockwise with a Phillips screwdriver. The removed screws are used to fix the Interface Board.
- When removing the fourth screw, hold the slot cover with your hand so it will not fall.
- To replace from other Interface Board, remove the Interface Board following the procedure in “How to remove the Interface Board” (x page 8).
- Install the Interface Board to the display device. (Fig. 2)
Insert the guide groove of the Interface Board aligned to the salient of the slot. Insert the bracket firmly all the way in. - Fix the Interface Board. (Fig. 3)
Tighten and fix with the four screws removed in Step 1)
chisamaliro
The removed slot cover is required when the unnecessary Interface Board is removed. Store it so it can be attached in the future.
How to remove the Interface Board
- Remove the Interface Board. (Fig. 1)
- Remove the four screws fixing the Interface Board by rotating counterclockwise with a Phillips screwdriver. The removed screws are used to fix the slot cover.
- Hold the handle of the Interface Board and remove it slowly.
- Attach the slot cover.
- Attach the stored slot cover to the blank slot, and tighten and fix with the four screws removed in Step 1).
- To replace with other Interface Board, attach the Interface Board following the procedure in “How to install the Interface Board” (x page 7).
chisamaliro
- Always attach the slot cover on the blank slot.
- Store the removed Interface Board inside an antistatic bag.
zofunika
The specifications of the Interface Board are as follows.
Interface Board for HDMI 2 input (Model No.: ET-MDNHM10)
| Compatible slot | SLOT NX specification | |
| Terminal yolumikizira | 2 sets, HDMI 19p, HDCP 2.3 compatible, Deep Color compatible | |
|
Compatible signal |
Chigamulo |
Moving image signal: 480i*1/576i*1 to 4 096 x 2 160
Still image signal: 640 x 400 to 3 840 x 2 400 (non- interlace) |
| Dot clock frequency | 25 MHz mpaka 594 MHz | |
|
miyeso |
m'lifupi | 151 mamilimita (5-15 / 16 ″) |
| msinkhu | 38.5 mamilimita (1-17 / 32 ″) | |
| kuzama | 142 mamilimita (5-19 / 32 ″) | |
| Kunenepa | 340 ] (12.0 ozs.) | |
*1 Pixel-Repetition signal (dot clock frequency 27.0 MHz) only
Interface Board for DVI-D 2 input (Model No.: ET-MDNDV10)
| Compatible slot | SLOT NX specification | |
| Terminal yolumikizira | 2 sets, DVI-D 24p, DVI 1.0 compliant (only single link supported), HDCP compatible | |
|
Compatible signal |
Chigamulo |
Moving image signal: 480i*1/576i*1 to 2 048 x 1 080
Still image signal: 640 x 400 to 1 920 x 1 200 (non- interlace) |
| Dot clock frequency | 25 MHz mpaka 162 MHz | |
|
miyeso |
m'lifupi | 151 mamilimita (5-15 / 16 ″) |
| msinkhu | 38.5 mamilimita (1-17 / 32 ″) | |
| kuzama | 142 mamilimita (5-19 / 32 ″) | |
| Kunenepa | 350 ] (12.3 ozs.) | |
*1 Pixel-Repetition signal (dot clock frequency 27.0 MHz) only
Zindikirani
- “SLOT NX” is a name of the slot unique to Panasonic Connect Co., Ltd. supporting the signal input for the 4K image.
- The video signal that can actually display will vary depending on the display device (projector or flat panel display) that the Interface Board is installed. For details, refer to the Operating Instructions of your display device.
Chopangidwa ndi:
Malingaliro a kampani Panasonic Connect Co., Ltd.
4-1-62 Minoshima, Hakata-ku, Fukuoka 812-8531, Japan
Wogulitsa kunja:
Panasonic Connect Europe GmbH
Woyimira Wovomerezeka ku EU:
Malo Oyesera a Panasonic
Winsbergring 15, 22525 Hamburg, Germany
Wotumiza kunja kwa UK;
Panasonic Connect UK,
a branch of Panasonic Connect
Europe GmbH,
Maxis 2, Western Road, Bracknell,
Berkshire, RG12 1RT
Malingaliro a kampani Panasonic Connect Co., Ltd.
Web Website: https://panasonic.net/cns/projector/
© Panasonic Connect Co., Ltd. 2022
Panasonic Connect North America
Mawiri a Riverfront Plaza, Newark, NJ 07102
TEL: (877) 803 - 8492
Gawo limodzi la Panasonic Canada Inc.
5770 Ambler Drive, Mississauga, Ontario L4W 2T3 TEL: (905) 624 – 5010
Zolemba / Zothandizira
 |
Panasonic ET-MDNHM10 Interface Board [pdf] Buku la Malangizo ET-MDNHM10, ET-MDNDV10, ET-MDNHM10 Interface Board, ET-MDNHM10, Interface Board, Board |
Pulojekiti | Panasonic Global 
