GSD WT2JM2601B Wifi Module Buku Logwiritsa Ntchito

GSD WT2JM2601B Wifi Module

• Module ya WIFI IEEE 802.11 b/g/n 2T/2R
• Number Model: WT2JM2601B

Kufotokozera Zamalonda

lachitsanzo	Module ya WIFI
Name mankhwala	WT2JM2601B
Standard	802.11 b / g / n
Chiyankhulo	USB
Mtengo Wosamutsa Data	1,2,5.5,6,11,12,18,22,24,30,36,48,54,60,90 ndi kuchuluka kwa 300Mbps
Kusinthasintha Njira	DQPSK,DBPSK,CCK(802.11b) QPSK,BPSK,16QAM,64QAM with OFDM (802.11g) QPSK,BPSK,16QAM,64QAM with OFDM (802.11n)
Kuyenda Kwambiri	2412 ~ 2462 MHz
Njira Yogwiritsira Ntchito	zomangamanga
Security	WEP, TKIP, AES, WPA, WPA2
Opaleshoni Voltage	3.3V ± 10%
Kugwiritsa Ntchito Masiku Ano	＜ 750mA
Mtundu wa Antenna	PIFA
opaleshoni Kutentha	0 ~ 60°C kutentha kozungulira
yosungirako Kutentha	-40 ~ 80 ° C yozungulira kutentha
chinyezi	5 mpaka 95% pazipita (zopanda condensing)

The WT2JM2601B is a 2.4GHz WIFI 2×2 MIMO module. This module provides a high level of integration with a dual-stream IEEE 802.11n MAC/ base band /radio.The WLAN operation supports 20MHz,40MHz channels for data rates up to 300Mbps. It fully complies with IEEE 802.11 b/g/n feature rich wireless connectivity at high standards,delivers reliable,cost-effective, throughput from an extended distance.

Zambiri Zamalonda

• Complies with IEEE 802.11b/g/n for 2.4GHz Wireless LAN.
• Njira ziwiri zotumizira ndi ziwiri (2T2R)
• Imagwira ntchito ndi maukonde onse omwe alipo.
• Imatha mpaka 128-Bit WEP Encryption.
• Ufulu woyendayenda mukamalumikizidwa.
• KUPUKA mpaka 300 Mbps High-Speed ​​Transfer Rate mumayendedwe a 802.11n.
• Operating Systems：Linux,Windows
• Kugwiritsa ntchito mphamvu zochepa.
• Yosavuta kukhazikitsa ndi kukhazikitsa.
• Kuthamanga kwambiri kwa USB 2.0 mawonekedwe
• Ovomerezeka ROHS

Ndondomeko ya Mtundu

CHidziwitso:

• chonde sungani mankhwalawa ndi zowonjezera kumalo omwe ana sangathe kuwakhudza;
• osawaza madzi kapena madzi ena pa mankhwalawa, apo ayi angayambitse kuwonongeka;
• musayike mankhwalawa pafupi ndi gwero la kutentha kapena kuwala kwa dzuwa, apo ayi zingayambitse kupunduka kapena kusagwira ntchito;
• chonde sungani mankhwalawa pamoto woyaka kapena wamaliseche;
• chonde musakonze izi nokha. Ogwira ntchito oyenerera okha ndi omwe angakonzedwe.

Chidziwitso cha FCC

Chida ichi adayesedwa ndikupeza kuti chikutsatira malire a chipangizo chamagetsi cha Class B, kutengera gawo la 15 lamalamulo a FCC. Malirewa adapangidwa kuti aziteteza moyenera kusokonezedwa ndi malo okhala. Chidachi chimapanga, chimagwiritsa ntchito ndipo chimatha kutulutsa mphamvu zamagetsi ndipo, ngati sichinaikidwe ndikugwiritsidwa ntchito mogwirizana ndi malangizo, zitha kusokoneza kuyankhulana kwawailesi. Komabe, palibe chitsimikizo kuti kusokonezedwa sikungachitike pakukhazikitsa kwina. Ngati chipangizochi chikuyambitsa vuto pakulandila wailesi kapena wailesi yakanema, zomwe zingadziwike mwa kuzimitsa zida zonse, wogwiritsa ntchitoyo amalimbikitsidwa kuti ayesere kusokoneza mwa njira imodzi kapena zingapo izi:

• Konzaninso kapena sinthani antenna yolandila.
• Lonjezani kupatukana pakati pazida ndi wolandila.
• Lumikizani zida zogulitsira pa dera losiyana ndi lomwe wolandirayo walumikizidwa.
• Funsani wogulitsayo kapena waluso pa TV / TV kuti akuthandizeni.

Zida izi zimagwirizana ndi Gawo 15 la Malamulo a FCC. Ntchito ikugwirizana ndi izi:

1. Chida ichi sichingayambitse mavuto, ndipo
2. Chida ichi chiyenera kuvomereza kusokonezedwa kulikonse komwe kulandiridwa, kuphatikiza kusokonezedwa komwe kumatha kuyambitsa ntchito yosafunikira. Zosintha zilizonse zosavomerezedwa ndi chipani chomwe chimayang'anira kutsata kungachititse kuti wogwiritsa ntchitoyo asagwiritse ntchito zida zake.

The module is limited to OEM installation ONLY. The OEM integrator is responsible for ensuring that the end-user has no manual instruction to remove or install module. This module has been assessed against the following FCC rule parts: CFR 47 FCC Part 15 C (15.247, DTS). It is applicable to the modular transmitter。 This radio transmitter FCC ID: 2AC23-WT2J has been approved by Federal Communications Commission to operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device. The concrete contents to check are the following three points.

1. Must use antenna such as PIFA antenna with gain not exceeding 1.26dBi;
2. Iyenera kukhazikitsidwa kuti wogwiritsa ntchitoyo asathe kusintha mlongoti;
3. Feed line should be designed in 50ohm Fine tuning of return loss etc. can be performed using a matching network. The antenna shall not be accessible for modification or change by the end user

The module complies with FCC Part 15.247 and applies for limited module approval.

Upangiri Wotsogolera

The final host / module combination may also need to be evaluated against the FCC Part 15B criteria for unintentional radiators in order to be properly authorized for operation as a Part 15 digital device. The user’s manual or instruction manual for an intentional or unintentional radiator shall caution the user that changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. In cases where the manual is provided only in a form other than paper, such as on a computer disk or over the Internet, the information required by this section may be included in the manual in that alternative form, provided the user can reasonably be expected to have the capability to access information in that form. To ensure compliance with all non-transmitter functions the host manufacturer is responsible for ensuring compliance with the module(s) installed and fully operational. For example, if a host was previously authorized as an unintentional radiator under the Declaration of Conformity procedure without a transmitter certified module and a module is added, the host manufacturer is responsible for ensuring that the after the module is installed and operational the host continues to be compliant with the Part 15B unintentional radiator requirements.and Part 15C intentional radiator requirements. The use condition limitations extend to professional users, then instructions must state that this information also extends to the host manufacturer’s instruction manual. This module is a limit modules. host manufacturer should confirm with module manufacturer for the installation method in end system. RF exposure evaluation when it is necessary to demonstrate compliance in a specific host.

Trace antenna designs: applicable.
Any deviation(s) from the defined parameters of the antenna trace, as described by the instructions, require that the host product manufacturer must notify the module grantee that they wish to change the antenna trace design. In this case, a Class II permissive change application is required to be filed by the grantee, or the host manufacturer can take responsibility through the change in FCC ID (new application) procedure followed by a Class II permissive change application. The device must be professionally installed. The intended use is generally not for the general public. It is generally for industry/commercial use. The connector is within the transmitter enclosure and can only be accessed by disassembly of the transmitter that is not normally required. The user has no access to the connector. Installation must be controlled. Installation requires special training.

The module is limited to installation in mobile application. Host device must be operated at a minimum of 20cm between people. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Antennas:

mlongoti	Pafupipafupi (MHz)	Mtundu wa Antenna	MAX Antenna Gain (dBi)
1	2412-2462	PIFA mlongoti	1.26
2	2412-2462	PIFA mlongoti	1.26

Please notice that if the FCC identification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: “Contains FCC ID:2AC23-WT2J” any similar wording that expresses the same meaning may be used.

Detail instructions from the module manufacturer

Separate approval is required for all other operating configurations, including portable configurations with respect to Part 2.1093 and different antenna configurations. The module is limited to OEM installation only. The OEM integrator is responsible for ensuring that the end-user has manual instructions to remove or install the module.
Must use the device only in host devices that meet the FCC/ISED RF exposure category of mobile, which means the device is installed and used at distances of at least 20 cm from persons. The end user manual shall include FCC Part 15 /ISED RSS GEN compliance statements related to the transmitter as show in this manual. Host manufacturer is responsible for compliance of the host system with module installed with all other applicable requirements for the system such as Part 15 B, ICES 003. Any company of the host device which installs this modular should perform the test of radiated & conducted emission and spurious emission etc. according to FCC Part 15C: 15.247 and 15.209 & 15.207, 15B class B requirement, only if the test result complies with FCC part 15C: 15.247 and 15.209 & 15.207, 15B class B requirement. Then the host can be sold legally.
The host product manufacturer is responsible for compliance with any other FCC rules that apply to the host not covered by the modular transmitter grant of certification. If the grantee markets their product as being Part 15 Subpart B compliant (when it also contains unintentional-radiator digital circuity), then the grantee shall provide a notice stating that the final host product still requires Part 15 Subpart B compliance testing with the modular transmitter installed. This modular transmitter is only FCC-authorized for the specific rule parts (47CFR Part 15.247) listed on the grant, and that the host product manufacturer is responsible for compliance to any other FCC rules that apply to the host not covered by the modular transmitter grant of certification. Host manufacturer is strongly recommended to confirm compliance with FCC/ISED requirements for the transmitter when the module is installed in the host. The use condition limitations extend to professional users, then instructions must state that this information also extends to the host manufacturer’s instruction manual. This module is stand-alone modular. If the end product will involve Multiple simultaneously transmitting condition or different operational conditions for a stand-alone modular transmitter in a host, host manufacturer has to consult with module manufacturer for the installation method in the end system. Refer to the minimum antenna gain requirements and antenna type (PIFA) that are approved for use with this module detailed in the previous sections. The use of other antennas will require additional certification procedures for the host system with FCC and ISED Canada.

This equipment complies with FCC and ISED-Canada radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed in host systems that are installed and operated with a minimum distance of 20cm between the radiator & people. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter except as permitted by FCC and ISED-Canada multie-transmitetr rules. The module is limited to installation in mobile application. For a normal application, for example, A television, host systems that are installed and operated with a minimum distance of 20cm between the radiator & people. If the end-user really needed to install in host systems that are installed and operated with a distance less than 20cm between the radiator & people, for example, a cell phone or laptop, the host systems need to comply with the requirements in KDB 996369 D03 OEM Manual v01 and KDB 996369 D04 Module Integration Guide v02. The module is not intended for general public, it must be professionally installed.

Zomwe zimagwiritsidwa ntchito pa module:

• yakanema 
  • polojekiti

For other devices,A special driver needed to be installed on the host before starting normal use for the module, and it is different for different kinds of hosts. Please contact us for more detail before installing on a host. For more information, please refer to the KDB 996369 D03 OEM Manual v01 and KDB 996369 D04 Module Integration Guide v02. The end user manual shall include FCC Part 15 /ISED RSS GEN compliance statements related to the transmitter as shown in below in addition to any other relevant statements or labeling requirements from e.g FCC Part 15 or the Canadian ICES standards. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:

1. Chida ichi sichingayambitse kusokoneza.
2. This device must accept any interference, including interference that may cause undesired operation of the device. To ensure compliance with FCC and ISED RF exposure requirements this device must be installed to provide a minimum of 20cm between the device and people.

Host manufacturer is strongly recommended to confirm compliance with FCC/ISED requirements for the transmitter when the module is installed in the host according to FCC Part 15.247, RSS-247, and FCC part 15 C. This modular transmitter is only FCC authorized for the specific rule parts (47CFR Part 15.247) listed on the grant, and the host product manufacturer is responsible for compliance with any other FCC rules that apply to the host not covered by the modular transmitter grant of certification such as ICES-003 and FCC Part 15 B. The use condition limitations extend to professional users, then instructions must state that this information also extends to the host manufacturer’s instruction manual. This module is stand-alone modular. If the end product will involve Multiple simultaneous transmitting condition or different operational conditions for a stand-alone modular transmitter in a host, host manufacturer has to consult with module manufacturer for the installation method in the end system.

Chiwonetsero cha Canada

Chipangizochi chimagwirizana ndi ma RSS osavomerezeka a Industry Canada. Ntchito ikugwirizana ndi izi:

1. Chida ichi sichingayambitse kusokoneza; ndipo
2. Chipangizochi chiyenera kuvomereza kusokonezedwa kulikonse, kuphatikiza kusokonekera komwe kungayambitse kusayenerera kwa chipangizocho.

Please notice that if the ISED certification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: “Contains IC:12290A-WT2J” any similar wording that expresses the same meaning may be used.

Chotumizira ichi sichiyenera kukhala chophatikizira kapena kugwira ntchito limodzi ndi mlongoti wina aliyense kapena chopatsilira. Zipangizozi ziyenera kukhazikitsidwa ndikugwiritsidwa ntchito osachepera 20 masentimita pakati pa rediyeta ndi thupi lanu.

This radio transmitter [12290A-WT2J] has been approved by Innovation, Science and Economic Development Canada to operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device.

Zomwe zili mkati mwa konkire zowunika ndi mfundo zitatu zotsatirazi.

1. Must use antenna such as PIFA antenna with gain not exceeding 1.26dBi;
2. Iyenera kukhazikitsidwa kuti wogwiritsa ntchitoyo asathe kusintha mlongoti;
3. Mzere wa chakudya uyenera kupangidwa mu 50ohm

Fine tuning of return loss etc. can be performed using a matching network. The antenna shall not be accessible for modification or change by the end user.

Chidziwitso ku chophatikiza cha OEM

Must use the device only in host devices that meet the FCC/ISED RF exposure category of mobile, which means the device is installed and used at distances of at least 20cm from persons. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. The end user manual shall include FCC Part 15 /ISED RSS GEN compliance statements related to the transmitter as show in this manual(FCC/ICanada statement). Host manufacturer is responsible for compliance of the host system with module installed with all other applicable requirements for the system such as Part 15 B, ICES 003. Host manufacturer is strongly recommended to confirm compliance with FCC/ISED requirements for the transmitter when the module is installed in the host.

The use condition limitations extend to professional users, then instructions must state that this information also extends to the host manufacturer’s instruction manual. This module is stand-alone modular. If the end product will involve Multiple simultaneous transmitting condition or different operational conditions for a stand-alone modular transmitter in a host, host manufacturer have to consult with module manufacturer for the installation method in end system.

Any company of the host device which install this modular should perform the test of radiated & condicted emission and spurious emission etc. according to FCC Part 15C: 15.247 and 15.209 & 15.207, 15B class B requirement, only if the test result comply with FCC part 15C: 15.247 and 15.209 & 15.207, 15B class B requirement. Then the host can be sold legally. This modular transmitter is only FCC authorized for the specific rule parts ( 47CFR Part 15.247 ) listed on the grant, and that the host product manufacturer is responsible for compliance to any other FCC rules that apply to the host not covered by the modular transmitter grant of certification. Host manufacturer is strongly recommended to confirm compliance with FCC/ISED requirements for the transmitter when the module is installed in the host. Must have on the host device a label showing Contains FCC ID: 2AC23-WT2J or IC: 12290A- WT2J Both FCC ID and IC ID are not to be placed on the host at the same time and only hosts going into the US can use the FCC ID and only hosts going into Canada can use the IC ID.

Zolemba / Zothandizira

GSD WT2JM2601B Wifi Module [pdf] Buku Logwiritsa Ntchito WT2J, 2AC23-WT2J, 2AC23WT2J, WT2JM2601B Wifi Module, WT2JM2601B, Wifi Module, Module