FREDRICK RAMOND FR31268, FR31265 Chandelier Instruction Manual

FREDRICK RAMOND FR31268, FR31265 Chandelier

NALA

1. Pezani malo omveka bwino omwe mungagwiritse ntchito.
2. Chotsani zinthu ndi magalasi kuchokera ku katoni.
3. Mosamala review malangizo asanayambe msonkhano.

STEPI 1

1. Feed wire through stem (S) or stems and loop (L).
2. Secure stems together if needed. Note fixture is supplied with multiple stem not all stems have to be used. Fixture can be mounted as a flush
3. Secure bottom stem (S) to coupler (Z) at the top of of fixture.
4. Secure top stem to loop (L)
5. Glass assembly can now be started

KUSINTHA KWA GALASI

Zindikirani: It is recommended that the glass be installed after fixture is hung.

1. To install the glass it will be necessary to remove the decorative
   threaded screw (1), located in the back glass bracket (2) – see Drawing 2.
2. Next take glass (3) and slip top of glass, with hole, into the glass bracket (2) and align the glass hole with the threaded hole in the back of the glass bracket.

NOTE: FIXTURE HAS TWO SIZES OF GLASS. THE LARGE GLASS LENS GOES ON THE BRACKET IN LINE WITH THE SOCKET. BOTH SIZES OF GLASS INSTALL IN THE SAME MANNER.
NOTE: It is recommended that you install the lens of glass opposite from the first one installed in order to keep fixture balanced during this process. Repeat process until all glass is installed.

Malangizo Okwezera

for fixtures exceeding 50 LBS. when assembled

ayambe apa

1. Pezani malo omveka bwino omwe mungagwiritse ntchito.
2. Chotsani zinthu ndi magalasi kuchokera ku katoni.
3. Mosamala review malangizo asanayambe msonkhano.

 

1. Shut off electrical current before starting. If the fixture you are replacing is turned on and off by a wall switch, simply turn the switch off. If not, remove the appropriate fuse (or open the circuIt breakers) until the fixture is dead.
   • DO NOT RESTORE CURRENT – EITHER BY FUSE, BREAKER, OR SWITCH – UNTIL THE NEW FIXTURE IS COMPLETELY WIRED AND IN PLACE.
2. Supply wires shall enter the outlet box (A) through any knockout EXCEPT the top center knockout – see Drawing 1.

1. Fixture is to be mounted by a 1/4IP threaded pipe, (not supplied). Pipe should be anchored to structure or bridging member with sufficient strength to support 4 times the fixtures weight – see Drawing 2.
2. Adjust pipe so 1” of the 1/4-18 NPS threaded pipe extends into the junction box, at the centerknock out.

1. Thread pipe coupler (B) onto the installed pipe, in the ceiling, protruding through junction box (A). Secure in place by tightening screws (C) – see Drawing 1.
2. Thread hex nut (J) onto threaded pipe (E). Thread loop (K) onto end of threaded tube (E). Secure loop in place by tightening hex nut (J) against loop (K) to secure loop to pipe.
3. Thread hex nut (D) onto threaded pipe (E). Thread pipe (E) into coupler (B). Adjust loop height so that half of the exterior threads on loop (K) are exposed, when canopy (L) is slipped over loop and held up to the ceiling. After adjustment is done tighten hex nut (D) against coupler (B) to secure pipe (E) in position.
4. Next take assembled fixture (without the glass) and using Quick link hook fixture onto loop (K).
5. Feed wires and cables through center hole of canopy loop and make all necessary wiring connections following instruction sheet (IS 18) provided. Make sure to attach safety cable to joist or structure independent of the junction box. Follow instruction sheet (IS-SCC) provided.
6. After all wiring and cable installation is complete. Slip canopy (L) up to ceiling along with screw collar ring (M). Hold canopy in place on ceiling and thread on screw collar ring to secure canopy into place.
7. Glass can now be mounted onto fixture. Follow instructions on the “FIXTURE ASSEMBLY” instructions.

FRIS18

WIRING AND GROUNDING INSTRUCTIONS

Chenjezo la Chitetezo: Read wiring and grounding instructions [FRIS 18] and any additional directions. Turn power supply off during installation. If new wiring isrequired, consult a qualified electrician orlocal authorities for code requirements.

STEP 1 WIRING INSTRUCTIONS
Zosintha Zam'nyumba

1. Connect positive supply wire (A) (typically black or the smooth, unmarked side of the two-conductor cord) to positive fixture lead (B) with appropriately sized twist on connector – See Drawing 1 or 2.
2. Connect negative supply wire (C) (typically white or the ribbed, marked side of the two-conductor cord) to negative fixture lead (D)
3. Chonde onani malangizo omwe ali pansipa kuti mumalize kulumikizana ndi magetsi.

Zokonza Panja

1. Connect positive supply wire (A) (typically black or the smooth, unmarked side of the two-conductor cord) to positive fixture lead (B) with appropriately sized twist on connector – See Drawing 1 or 2.
2. Connect negative supply wire (C) (typically white or the ribbed, marked side of the two-conductor cord) to negative fixture lead (D)
3. Phimbani mapeto otseguka a zolumikizira ndi silicone sealant kuti mupange chisindikizo chopanda madzi.
   • Mukayika choyika pakhoma, gwiritsani ntchito caulk kuti mutseke mipata pakati pa mbale yoyikira (backplate) ndi khoma. Izi zidzathandiza kuti madzi asalowe m'bokosi. Ngati pamwamba pa khoma ndi lap siding, gwiritsani ntchito caulk ndi nsanja yoyikapo mwapadera.
4. Chonde onani malangizo omwe ali pansipa kuti mumalize kulumikizana ndi magetsi.

STEP 2 GROUNDING INSTRUCTIONS

Flush Mount Fixtures

For positive grounding in a 3-wire electrical system, fasten the fixture ground wire (E) (typically copper or green plastic coated) to the fixture mounting strap (1) with the ground screw (2) – See Drawing 1.
Zindikirani: On straps forscrew supported fixtures, first install the two mounting screws in strap. Any remaining tapped hole may be used for the ground screw.

Zosintha za Chain Hung

Loop fixture ground wire (E) (typically copper or green plastic coated) under the head of the ground screw (2) on fixture mounting strap (1) and connect to the loose end of the fixture ground wire directly to the ground wire of the building system with appropriately sized twist-on connectors – See Drawing 2.

Zosintha za Post-Mount

Connect fixture ground wire (E) (typically copper or green plastic coated) to power supply ground with appropriately sized twist-on connector inside post. Cover open end of connector with silicone sealant to form a watertight seal – See Drawing 3.

A Division of Hinkley
33000 PIN OAK PARKWAY | AVON LAKE, OHI0 44012
toll free 800.446.5539 I phone 440.653.5500

Zolemba / Zothandizira

FREDRICK RAMOND FR31268, FR31265 Chandelier [pdf] Buku la Malangizo FR31268, FR31265, FR31268 FR31265 Chandelier, FR31268 Chandelier, FR31265 Chandelier, Chandelier

Zothandizira

• HINKLEY - Mafani Owunikira ndi Kudenga - Tsamba Lanyumba