FREDRICK RAMOND FR30506 Buku Lachidziwitso la Kuwunikira ndi Mafani a Ceiling

FREDRICK RAMOND FR30506 Lighting and Ceiling Fans

Mounting Instructions FR30506

ayambe apa

1. Pezani malo omveka bwino omwe mungagwiritse ntchito.
2. Chotsani zinthu ndi magalasi kuchokera ku katoni.
3. Mosamala review malangizo asanayambe msonkhano.

Zimitsani magetsi musanayambe. Ngati chosinthira chomwe mukuchisinthacho chayatsidwa ndikuzimitsidwa ndi chosinthira pakhoma, ingozimitsani. Ngati sichoncho, chotsani fusesi yoyenera (kapena tsegulani zowononga madera) mpaka chojambulacho chafa.

• DO NOT restore current – either by fuse, breaker, or switch – until the new fixture is completely wired and in place.

1. Dziwani kutalika komwe pendant idzayikidwe.
2. The fixture is supplied with assorted stem sizes. Determine what combinations of stems are needed to achieve desired length – see Drawing 1 and 2 for part reference.
   
   
3. Dulani tsinde pamwamba pa waya ndi tsinde loyamba pamwamba pa tsinde, lalitali kwambiri poyamba. Bwerezani izi mpaka tsinde zonse zofunika zitalumikizidwa pamodzi.
4. Next slide screw collar ring (S) along wire and over stems, followed by the canopy (C).
5. Now slip wires through the center hole in the swivel attached to the mounting strap (A). Then thread swivel into top of last stem. Pendant is now ready to to be installed

 

1. To mount assembled pendant body to ceiling, first make all the necessary wiring connections using instruction sheet IS18 provided.
2. After all wiring connections are complete, tuck all wires into junction box (J) – see Drawing 2.
3.  Now attach mounting strap (A) to junction box (J) using two screws (B) NOT PROVIDED.
   
   ZINDIKIRANI: the back of mounting strap (A) should be flush against the ceiling. It should not be recessed into the ceiling or off of the ceiling surface.
4. Next slip canopy (C) up against the ceiling and thread screw collar (S) onto exposed portion of threaded section (L) and tighten to secure canopy to ceiling.
5. Refer to assembly instructions for attaching glass to pendant body.

Glass installation FR30506

1. Pezani malo omveka bwino omwe mungagwiritse ntchito.
2. Chotsani zinthu ndi magalasi kuchokera ku katoni.
3. Mosamala review malangizo asanayambe msonkhano.

 

1. To install glass (1) first thread coupler (2) off of center stem assembly (A) – see DRAWING 1. This will allow the glass cap (3) to slide along the center stem freely.
2. Prior to attaching the glass to the fixture body the bulb should be installed. English
3. Next take glass (1) and slip one side of bracket (B) into top of glass. Now slide glass over and slip opposite side of bracket (B) into top of glass. Rest glass on bracket (B)
4. Tsopano lowetsani kapu yagalasi (3) pansi pa dzenje pamwamba pa galasi ndi ulusi wophatikizana (2) pansi pa tsinde lapakati kuti mutseke galasi.

malangizo opangira ma waya

SAFE TY WARNI NG: WERENGANI WIRIN G NDIPO KUGULITSA MALANGIZO NS (NDI 18) NDI MALANGIZO ENA ALIYENSE. ZImitsani MPHAMVU POYANG'ANIRA. NGATI WIRING WATSOPANO AKUFUNIKA, FUNANI ANTHU WOPHUNZIRA AMA ELEKITI KAPENA ABOMALA AMENE TIKUFUNA ZOFUNIKIRA MAKHODI.

malangizo a zingwe

1. Connect positive supply wire (A) (typically black or the smooth, unmarked side of the two-conductor cord) to positive fixture lead (B ) with appropriately sized twist on connector – see Ora wings 1 o r 2.
2. Connect negative supplywi re (C) (typically white or the ribbed, marked side of the two-conductor cord) to negative fixture lead (D).
3. Please refer to the grounding instructions below to complete all electrical I connections

Zokonza Panja

1. Connect positive supply wire (A) (typically black or the smooth unmarked side of the two-conduce tor cord) to positive fixture lead (B)with appropriately sized twist on connector – see Drawings 2 or 3.
2. Connect negative supp ly wire {C) (typically white or the ribbed, marked side of the two-conductor cord) to negative fixture lead (D).
3. Cover open end of connectors w ith silicone sealant to form a watertight sea l. 181 If installing a wall mount fixture, use caulk to seal gaps between the fixture mounting plate (backplate) and the wall. This wil l help prevent water from entering the outlet box. If the wal I surface is lap siding, us Caulk and a fixture mounting plat form specially.
4. Please refer to the grounding Instructions below to complete all electrical I connections.

malangizo oyambira

Flush Mount Fixtures

For positive grounding in a 3-wire electrical system, fasten the fixture ground wire (E) (typically copper or green plastic coated) to the fixture mounting strap (M) with the ground screw (5) -see Chojambula 1.

Zindikirani: Pazingwe zomangira zomangira, choyamba ikani zomangira ziwirizo mu lamba. Bowo lililonse lomwe latsala litha kugwiritsidwa ntchito ngati wononga.

Zosintha za Chain Hung

Loop fixture ground wire (E) (typicallycoppe r or green plastic coated)under the head of the ground screw (5) on fixture mounting strap (M) and connect to the loose end of the fixture ground wire directly to the ground wire of the building system with appropriately sized twist-on connectors – see Drawing 2 .

Zosintha za Post-Mou nt

Connect fixture ground wire (E) (typically copper or green plastic coated) to power supply ground with appropriately sized twist-on connector inside post. Cover open end of connector with silicone sealant to form a watertight seal – see Chojambula 3.

HINKLEY 33000 Pin Oak Parkway, Avon Lake, OH 44012 8 00.446.5539 / 440 .653.5500 hinkley.com

Zolemba / Zothandizira

FREDRICK RAMOND FR30506 Lighting and Ceiling Fans [pdf] Buku la Malangizo FR30506 Lighting and Ceiling Fans, FR30506, FR30506 Ceiling Fans, FR30506 Lighting Fans, Lighting and Ceiling Fans, Lighting Fans, Ceiling Fans, FR30506 Fans, Fans

Zothandizira

• HINKLEY - Mafani Owunikira ndi Kudenga - Tsamba Lanyumba