FREDRICK RAMOND 30204 Buku Lolangiza Lakuwunikira ndi Kuyika Padenga

FREDRICK RAMOND 30204 Lighting and Ceiling Fan

malangizo

1. Pezani malo omveka bwino omwe mungagwiritse ntchito.
2. Chotsani zinthu ndi magalasi kuchokera ku katoni.
3. Mosamala review malangizo asanayambe msonkhano.

Msonkhano

1. To begin, it will be necessary to finish assembling the main body (1). This is accomplished by attaching the bottom ring (2) to the main body.
2. Take the bottom ring (2) and slip the end of threaded tube (3) through the center hole in the bottom ring center hub. Hold in position and thread on bottom knob (4) and tighten to secure ring.
3. Fixture can now be installed. This is accomplished by following instruction sheet (IS-19) provided. Please read all the instruction before starting installation.

KUSINTHA KWA GALASI

1. To begin glass strand installation, first unwrap the strands from their packing. Next arrange them according to size. There are 4 sizes of glass strands. Extra long (EX), long (L), medium (M) and short (S) – see Drawing 2.
2. The extra long glass strands, have a hook on both ends. They are used for the top half of the fixture. The end of the strand with the large glass rock is the top. Take the hook on this end and hook it through one of the holes on the top ring (TR). Now take the bottom hook of the strand and hook it through one of the holes in the top of bottom ring (BR). Make sure when attaching the extra long strands that you accidentally do not skip any holes.
3. Now the remaining long (L), medium (M) and short (S) have one hook at one end. These can be hung off the bottom holes (BH) in the bottom half of the bottom ring
   (BR).

ogwiritsa Malangizo

CHENJEZO LOTETEZA: WERENGANI MALANGIZO OGWIRITSA NTCHITO (NDI 18) NDI MALANGIZO ENA ALIYENSE. ZImitsani MPHAMVU POYANG'ANIRA. NGATI AMAFUNIKA WIRING WATSOPANO, FUMANANI NDI WOPHUNZITSIRA MATHAMVU KAPENA ABOMLEZI WAKUTI MUDZAFUNE ZOFUNIKIRA MAKHODI.

1. Shut off electrical current before starting. If the fixture you are replacing is turned on and off by a wall switch, simply turn the switch off. If not, remove the appropriate fuse (or open the circuit breakers) until the fixture is dead.
   • DO NOT restore current – either by fuse, breaker or switch – until the new fixture is completely wired and in place.

Kupachika

1. Fasten mounting strap provided – see (1) to outlet box ( A) with the two 8-32 screws ( 2) not Drawing 1 .
2. Thread 2 – hex nuts ( 3a) and ( 3b) onto threaded tubing ( 4).
3. Thread one end of threaded tubing ( 4) into loop ( 5) a minimum of 1/2’’ to 3/4’’. Tighten hex nut ( 3a) against loop ( 5) to lock loop in position.
4. Thread other end of threaded tube ( 4) into mounting strap approximately 1/2’’.
5. Slip canopy ( B) over loop ( 5) and adjust height of loop so half of the threaded area on the loop is exposed – see Drawing 2 below. After loop height is adjusted, tighten hex nut (3b) up against mounting strap, tighten against mounting strap to lock loop and threaded tube in position.
6. Remove mounting strap ( 1) from junction box ( A), and thread third hex nut ( 3c) onto end of threaded tube ( 4) above the mounting strap, tighten against mounting strap to lock assembly in position.
7. Remount mounting strap to junction box.

Kusintha kwa Canopy

1. Kutenga unyolo, dziwani kutalika komwe mukufuna kuti mupachike chingwecho.
2. Gwirizanitsani mbali imodzi ya unyolo pamwamba pazitsulozo.
3. Now slip loop collar (6) and canopy (B) onto chain. — – see Drawing 2
4. Attach other end of chain to loop (5). Get assistance for this step since fixture may be heavy and difficult to hold while attaching the chain.

malangizo opangira ma waya

CHENJEZO WOtetezedwa: READ WIRIN G AND GROUNDING INSTRUCTIO NS (IS 18) AND ANY ADDITIONAL DIRECTIONS. TURN POWER SUPPLY OFF DURING INSTALLATION. IF NEW WIRING IS REQUIRED, CONSULT A QUALIFIED ELECTRICIAN OR LOCAL AUTHORITIES FOR CODE REQUIREMENTS

Zosintha Zam'nyumba

1. Connec t positive supply wire (A ) (typically black or the smooth, unmarked side of the two-conduc tor cord) to positive fixture lead (B) with appropriately sized twist on connector – see Dra w ings 1 or 2.
2. Connec t negative supply wire (C) (typically white or the ribbed, marked side of the two-conductor cord) to negative fixture lead (D).
3. Chonde onani malangizo omwe ali pansipa kuti mumalize kulumikizana ndi magetsi

Zokonza Panja

1. Connec t positive supply wire (A) (typically black or the smooth unmarked side of the two-conduc tor cord) to positive fixture lead (B) with appropriately sized twist on connector — see Drawings 2 or 3.
2. Connec t negative supply wire (C) (typically white or the ribbed, marked side of the two-conductor cord) to negative fixture lead (D).
3. Phimbani mapeto otseguka a zolumikizira ndi silicone sealant kuti mupange chisindikizo chopanda madzi.
   If installing a wall mount fixture, use caulk to seal gaps between the fixture mounting plate (backpla te) and the wall. This will help prevent water from entering the outlet box. If the wall surface is lap siding, use caulk and a fixture mounting platform specially.
4. Chonde onani malangizo omwe ali pansipa kuti mumalize kulumikizana ndi magetsi.

Malangizo okhazikika

Flush Mount Fixtures
Kuti mukhazikike bwino pamagetsi a mawaya atatu, yokani mawaya apansi (E) (amene nthawi zambiri amapaka pulasitiki yamkuwa kapena yobiriwira) ku lamba (M ) ndi zomangira (S) - onani Draw in g 3.
Chidziwitso: Pazingwe zomangira zomangira, choyamba ikani zomangira ziwirizo mu lamba. Bowo lililonse lomwe latsala litha kugwiritsidwa ntchito ngati wononga.

Zosintha za Chain Hung
Loop fixture ground wire (E) (typically coppe r or green plastic coated) under the head of the ground screw (S) on fixture mounting strap (M) and connect to the loose end of the fixture ground wire directly to the ground wire of the building system with appropriately sized twist-on connectors – see Draw in g 2.

Post-Mou nt Fixtur es
Connec t fixture ground wire (E) (typically copper or green plastic coated) to power supply ground with appropriately sized twist-on connector inside post. Cover open end of connector with silicone sealant to form a watertight seal – see Drawing 3.

Zolemba / Zothandizira

FREDRICK RAMOND 30204 Lighting and Ceiling Fan [pdf] Buku la Malangizo 30204 Lighting and Ceiling Fan, 30204, 30204 Lighting, 30204 Ceiling Fan, Lighting and Ceiling Fan, Ceiling Fan, Lighting