CCD12 Center Console Desk
Buku Lophunzitsira
Kulemera kwa katundu
Ma 45 lbs.
WIDTH x DEEPTH x HEIGHT
12.15 × 22.38 × 18.35
COLOR GRAY CATALOG NUMBER CCD12
CCD12 Center Console Desk
MITU YA NKHANI
Center console desk is designed to be used with optional powerstrip, PA9, hanging file kit CCDHF12, and laptop holder CCDLTH
The information contained in this document is the sole property of ADRIAN STEEL COMPANY. ADRIAN STEEL COMPANY retains the right to modify and/or change the product of its design at any time without prior notification.
Chiyambi / Ndemanga:
This Center Console Desk is designed for storage of chargers, power strip, CCDHF12, CCDLTH, AND PA9.
Zindikirani:
It is advised that all fasteners used in this assembly and installation should be checked for tightness at the following intervals: @ 2-weeks and again @ 6-weeks of operation. This preventive maintenance step must be completed to ensure your Center Console gives you long service life.
CENTER CONSOLE DESK FOR MISC USE.
- KUSAMALITSA -
|
|
|
|
|
|
|
|
Chenjezo
THE USE OF AIR IMPACT TOOLS CAN
ALL INSTALLATION HOLES SHOULD BE SEALED
INSPECT FOR FUEL TANK, FUEL LINES, BRAKE LINES, HIGH
TO AVOID DAMAGING THE VEHICLE ALWAYSIMPORTANT WARRANTY REQUIREMENTS
- KUSINTHA ZINTHU ZOTSATIRA ZA ADRIAN ZIZINDIKIRO ZOYENERA KUSONKHANA NDI/KOMA KUYANG'ANIRA KUDZACHITA CHITIDIKIRO CHA NTCHITO YANU.
- ALL HOLES DRILLED INTO VEHICLE SHOULD HAVE THE RAW METAL EDGES SEALED WITH A SELF -ETCHING PRIMER TO RESIST CORROSION AND POTENTIAL FASTENER POINT FAILURE.
- ZINTHU ZONSE ZOTSATIRA ZOGWIRITSA NTCHITO POIKIKITSA CHINTHU ZIMENEZI ZIYENERA KULIMBIKITSIDWA PA MITUNDU (MA) OMWE OTULULIDWA M'MALANGIZO AWA.
- MALANGIZO AWA AYENERA KUKHALA NDI GALIMOTO.
THE BASIC TOOLS NEEDED FOR MOST INSTALLATIONS
ZIPANGIZO ZOWONJEZERA PA KUYEKA KUTI NDIPO ZIDZIWIKIKA M'MFUNDO ZOTSATIRA.
If your vehicle contains carpet or a rubber floor mat you will need to prepare the mounting location.
Position the product to be installed into the vehicle and once your are satisfied with the mounting locations, mark the mounting locations. Using a 1-3/16” diameter carpet cutter (P/N: 31183-0). Select the appropriate floor spacers as shown in the illustration. Set those aside for use later into the installation process. Using the correct drill bit size for the selected plusnut, drill the mounting holes in the vehicle sheet metal to prepare for installing the plusnuts.
If you are thru-bolting at any of the locations simply drill a hole that is 1/16” larger than the bolt size(s) for those locations.
Once you have drilled the holes into the vehicle, the raw metal edges should be sealed using a self-etching primer to resist corrosion and potential fastener point failure. 
A PLUSNUT (RIVNUT) SETTING TOOL IS REQUIRED FOR PLUSNUT (RIVNUT) INSTALLATION AND IS SUPPLIED WITH THIS KIT. OR USE AN AIR POWERED PLUSNUT SETTING GUN.
1/4-20UNC Plusnut (FAS0052) Gwiritsani ntchito 3/8” dia. kubowola w/stop
FAS0080 SCREW, HXHD, 1/4-20UNCx2.00”, G8
FAS0067 WASHER, FLAT, 1/4”ID
22200-0 PLUSNUT CHIDA
5/16-18UNC Plusnut (FAS0091) Gwiritsani ntchito 1/2” dia. kubowola w/stop
FAS0095 SCREW, HXHD, 5/16-18UNCx2.00”, G8
FAS0086 WASHER, FLAT, 5/16”ID
22200-0 PLUSNUT CHIDA
Ikani mbiya ya thupi la plusut muzitsulo zachitsulo kudutsa dzenje mpaka flange itasungunuka ndi chitsulo.
Pogwiritsa ntchito 9/16 ″ wrench ya chida cha plusnut ndi wrench yachiwiri, ratchet, kapena chida cha mpweya, tembenuzani mutu wa hex bolt CW kuti mujambule ma flanges a nati mmwamba (ikani plusnut).
CCD12 CENTER CONSOLE DESK
| ITEM NO. | GAWO NUMBER | DESCRIPTION | CCD12/QT Y. |
| 1 | 37760-G | LID WELDMENT, CCD12 | 1 |
| 2 | 50045-G | BODY WELDMENT, CCD12 | 1 |
| 3 | HDWCCD12 | CCD12 HARDWARE CARTON | 1 |
| 4 | 25011-0 | DECAL LID LATCHED | 1 |
HDWCCD12
CCD12 HARD WARE KIT
| ITEM NO. | GAWO NUMBER | DESCRIPTION | HDWCCD12/QTY. |
| 1 | BAG50050 | FAJENER BAG FOR CCD12 | 1 |
| 2 | HDVV50050 | HARDWARE BAG FOR CCD10 AND CCD12 | 1 |
| 3 | 44388 | GROMMET,RUBBER, 1.5″ ID | 3 |
| 4 | 35295-B | MOLDED SLAM LATCH | 1 |
| 5 | CRT25386-1 | HARDWARE BOX FOR CCD | 1 |
HDW50050 HARDWARE BAG FOR CCD10 & CCD12
| ITEM NO. | GAWO NUMBER | DESCRIPTION | QTY. |
| 1 | BAG0507-A | 5″ x 7″ 3MIL AUTO BAG | 1 |
| 2 | Mtengo wa FAS0137 | Screw, Round Phillips Head, #6-3241375, Zinc plate | 2 |
| 3 | Mtengo wa FAS0138 | Nut Hex Flange, #6-32, Zinc Plate | 2 |
| 4 | 34341-0 | 9309K16 MCMASTER CARR BUMPER | 2 |
| 5 | 25384-0 | SPRING CLIP, CCD | 1 |
| 6 | F AS0030 | Screw, Round Phillips Head, #10-2441375 | 5 |
BAG50050 FASTENER BAG FOR CCD12
| ITEM NO. | GAWO NUMBER | DESCRIPTION | QTY. |
| 1 | BAG0507-A | .5″ x 7″ 3MIL AUTOBAG | 1 |
| 2 | Mtengo wa FAS0020 | Nut, Hex Flange, #10-24 | |
| 3 | Mtengo wa FAS0091 | Zowonjezera, 5/16 | 4 |
| 4 | Mtengo wa FAS0092 | Screw, Hex Hd, 5/16-18×1.50 Zn Plate, G8 | 4 |
| 5 | 21166-0 | ECCENTRIC WASHER | 4 |
| 6 | 03927-1 | Pansi Spacer Short | |
| 7 | 03927-2 | Tall Floor Spacer | 4 |
| 8 | Mtengo wa FAS0098 | Washer, Lock, Split, 5/16, Zinc Plate | 4 |
LID ASSEMBLY INSTALL
INSTALL CENTER FILE, AND GROMMETS
PRIOR TO INSTALLING LID, INSTALL ANY ACCESSORIES INSIDE CCD WITH INSTRUCTIONS SUPPLIED WITH ACCESSORIES. 
INSTALL INTO VEHICLE
DOUBLE CHECK ALL FASTENERS LOCATIONS TO BE SURE THAT ALL
FASTENERS ARE TIGHTENED TO SPECIFICATIONS.
YOUR INSTALLATION IS NOW COMPLETE!
IWANI KOPI IYI M’GALIMOTO KUTI MUZIKUMBUKIRA TSOGOLO!
ADRIAN STEEL COMPANY
WWW.ADRIANSTEEL.COM
906 JAMES STREET
ADRIAN, MI 49221
800-677-2726
Zolemba / Zothandizira
 |
ADRIAN STEEL CCD12 Center Console Desk [pdf] Buku la Malangizo CCD12 Center Console Desk, CCD12, Center Console Desk, Console Desk, Desk |
Adrian Steel | Ladder Racks, Van Accessories, Storage | Vehicle Upfits 
