FS S1150-8T2F PoE+ Switch Reset ndi Recovery System User Guide
FS S1150-8T2F PoE+ Sinthani Bwezerani ndi Njira Yobwezeretsa

Zolinga Zokonzekera

Table 1 zopangidwa ndi mitundu yama example

Series mankhwala Support version
Kusintha kwa PoE Series Chithunzi cha S3150-8T2FP

Mitu Yapaintaneti

Mitu Yapaintaneti

Masitepe Opaleshoni

Zida Zolumikizira

#According to the way of networking topo to connect PC and switch to network cable and Console. One end of the RJ-45 network cable isconnected to  the PC NIC, and the other end is connected to the SW’s network port. Connect one end of Console line USB to PC’s USBinterface, and the other end of RJ-45 is connected to console interface of front panel of switch.

Tsitsani Mapulogalamu Osintha

#After the connection is completed, there we recommend the super terminal, putty or Secure CRT tool to configure the switch.

Yatsani ndi Kugwiritsa Ntchito Mapulogalamu Olowera

#Energizing the switch, then open the installed login software, select the serial port of login mode, port through the device manager todetermine. Baud rate :115200, Data bits: 8, Parity: None, Stop bits: 1. (Reference below)
Logging in Software

ZINDIKIRANI: Nambala ya COM ikhoza kukhala viewed through device manager. (right click on my computer.>manage>device manager>port (COMandLPT)If it displays an unrecognized USB device, please download and install the corresponding driv

Kubwezeretsa System

*Please use Ctrl + P to enter the monitor # interface when restarting the switch, then configure the switch IP address. monitor#ip address 192.168.1.1 255.255.255.0

* Khazikitsani adilesi ya IP ya PC
Kubwezeretsa System

*Kenako konzani tftp
Kubwezeretsa System

* Kenako yambani kukweza dongosolo: thamangani tftp flash
Malangizo a Mapulogalamu

Pitani ku Factory Reset

Kukonzanso Zowonongeka

ngati file dzina silinalowetsedwe, kuyambitsa-config files will be deleted by default.

Recovery the Password of the Switch

Restart the switch

#After completing the above steps, power off and restart the switch. During the restart process, continuously press “CTRL + P” to enter theswitch system monitoring mode(monitor #) and view ndi file cha kusintha.
Restart the switch
PS. You can view kasinthidwe file under the switch as startup-config through dir.

View the Configuration File

A: Plaintext Encryption Solution
kasinthidwe File
kasinthidwe File

#By viewing the configuration file information, you can see that the user name and password configured on the switch is “username adminpassword 0 admin”, which indicates that the switch uses plaintext encryption, so directly restart the switch with the command: reboot, andthen log in switch with admin/admin.

B: Ciphertext Encryption Solution
Ciphertext Encryption Solution

#By viewing the configuration file information, you can see that the user name and password configured on the switch is “username adminpassword ******”, which indicates that the switch uses ciphertext encryption.

#Solution: The cipher text method can only choose to delete the original configuration file, but in order to retain the configuration file whenthe device can operate normally after logging to the switch, it’s need to back up the configuration file, the specific steps are as follows:

  1. First display all configuration information through the command: more startup-config, and then put the configuration information into theTXT file by copying and pasting.
  2. Chotsani kasinthidwe file and restart the switch.
    Ciphertext Encryption Solution
    Ciphertext Encryption Solution
    Ciphertext Encryption Solution
  3. Lowetsani kasinthidwe file, the steps are as follows:
    First modify the TXT file name to: startup-config, and then delete the username configuration in the document or modify the “usernameconfiguration” in the document to “username XXX password XXX”

After uploading the configuration file to the switch with the TFTP / FTP software, then load the configuration file with following commandand restart the device:
Ciphertext Encryption Solution

PS. Use the following two commands to view the configuration information of the switch: monitor#more startup-config / monitor#show configuration
Malo a GPS
https://www.fs.com

The information in this document is subect to change without notices. FS has made all efforts to ensure the accuracy of the information, but all information in this document does not constitute any kind of warranty.

Logo

Zolemba / Zothandizira

FS S1150-8T2F PoE+ Sinthani Bwezerani ndi Njira Yobwezeretsa [pdf] Wogwiritsa Ntchito
S1150-8T2F PoE Switch Reset and Recovery System, S1150-8T2F, PoE Switch Reset and Recovery System, Switch Reset and Recovery System, Reset and Recovery System

Zothandizira

Kusiya ndemanga

Anu email sati lofalitsidwa. Amafuna minda amalembedwa *